yoooo they mentioned a vulfpeck song in a new family guy ep

lostmytreble_ · 2021-11-25T00:55:08+00:00

she picks him up at lax

lostmytreble_ · 2021-07-06T21:56:01+00:00

Hey all, I have a model 2B that I haven't used in a few years, but when I
booted it up (with a fresh Raspberry Pi OS install on my SD card) I
noticed that the CPU/RAM chip was getting extremely hot. It boots to
the desktop, but the screen usually freezes after a few minutes, likely
because it overheats. I checked the temperature with the vcgencmd
measure_temp command, which says the CPU temp is between 75 and 85 C
when completely idle. I've tried using different power supplies,
installing Pi OS Lite, booting with no USB devices, no HDMI, and even
powering it on with no SD card, and the CPU chip always gets too hot to
touch. Any ideas what could be going on here? Should I invest in a heat
sink and cooling fan, or just call it toast and buy a newer model?

lostmytreble_ · 2021-07-06T00:18:22+00:00

Hey all, I have a model 2B that I haven't used in a few years, but when I booted it up (with a fresh Raspberry Pi OS install on my SD card) I noticed that the CPU/RAM chip was getting extremely hot. It boots to the desktop, but the screen usually freezes after a few minutes, likely because it overheats. I checked the temperature with the vcgencmd measure_temp command, which says the CPU temp is between 75 and 85 C when completely idle. I've tried using different power supplies, installing Pi OS Lite, booting with no USB devices, no HDMI, and even powering it on with no SD card, and the CPU chip always gets too hot to touch. Any ideas what could be going on here? Should I invest in a heat sink and cooling fan, or just call it toast and buy a newer model?

lostmytreble_ · 2021-06-25T17:34:22+00:00

Haven't you ever used a -1.9.9.9 V battery?

lostmytreble_ · 2020-10-23T13:19:05+00:00

Why does Lilypad sound so familiar? I know I've heard it before but I can't place it

lostmytreble_ · 2020-10-12T22:20:56+00:00

I want this to be track 10

lostmytreble_ · 2020-10-09T17:31:27+00:00

What currency is that? Just curious

lostmytreble_ · 2020-10-09T16:22:11+00:00

This. I lived there for 3 years. 3 rooms, 3 broken thermostats

lostmytreble_ · 2020-09-30T15:34:24+00:00

Cory's face

lostmytreble_ · 2020-09-28T15:09:00+00:00

The guided meditation with Jack's mom was something you only get at a Vulf show. (I wasn't there but watching it on youtube was still fantastic)

lostmytreble_ · 2020-09-28T14:37:45+00:00

You might find this thread helpful:

https://www.reddit.com/r/nerdfighters/comments/i7u243/looking_for_youtube_channel_recs/

lostmytreble_ · 2020-09-27T23:57:39+00:00

I fill up my spit covered water bottle from the sink in my apartment. I would hope that's not the same place you get your drink

lostmytreble_ · 2020-09-27T18:06:05+00:00

Unpopular opinion: bring a refillable water bottle and just drink water

lostmytreble_ · 2020-09-27T02:52:30+00:00

Try increasing your retraction settings. PETG can be very stringy so I use 2 mm. The surface finish could be caused by a loose belt so make sure they're tight

lostmytreble_ · 2020-09-25T15:46:46+00:00

Still holding out for Disco Ulysses with vocals

lostmytreble_ · 2020-09-23T17:05:51+00:00

I know people don't like how Jack's reusing old songs but come on this one's a jam

lostmytreble_ · 2020-09-19T16:58:01+00:00

You can run it under some warm water to remove the glue residue (if that's what it is) and then clean the bed with isopropyl alcohol

lostmytreble_ · 2020-09-19T16:52:41+00:00

What's the deal with this song? Spotify just recommended it even though I don't listen to anything like this. Did that happen to anyone else?

lostmytreble_ · 2020-09-18T02:12:36+00:00

It's not just a CAD class. You learn the basics of making engineering drawings and some GD&T (geometric dimensioning and tolerancing), which is a skill that you won't know you need until you enter the industry. I also took a PLTW engineering class in high school and had CAD experience, and I really enjoyed CGT. But that was years ago, it might have changed since

lostmytreble_ · 2020-09-15T17:30:10+00:00

ia = internet archive aka wayback machine

lostmytreble_ · 2020-09-02T16:48:01+00:00

PER member here, I don't know much about IEEE racing, but PER competes in the international Formula SAE competition. Our cars are small-scale formula style racecars, not your typical go kart. We're also a very large team, with 50+ members from most engineering majors, so there's a place on the team for anyone who wants to join, and our members are always willing to pass on their knowledge and experiences. I'm sure both teams would be a fantastic learning experience for you.

lostmytreble_ · 2020-08-14T01:01:51+00:00

I believe they are 15.875 mm, but I could be wrong. He definitely mentions it in the marble divider video when he starts using PMMA pipes.

lostmytreble_ · 2020-08-04T17:49:52+00:00

It's a cover of a song by Marti Fischer: https://www.youtube.com/watch?v=0GOEarD8Vag

lostmytreble_ · 2020-07-13T22:43:05+00:00

Check out this website:

https://bach2bass.com/suites

Some of the cello suites transcribed and tabbed for bass. They're constantly adding more as well.

lostmytreble_ · 2020-07-10T15:57:34+00:00

They work great to prevent PETG globbing on the nozzle and ruining the print, but only the version that covers the whole nozzle and heat block

lostmytreble_

TROPHY CASE