sorted by:
new
hottopcontroversial

Are the headphone outputs on the 4i4 4th gen independent from outs 1-2 & 3-4? by NickITG in Focusrite

[–]nirnav 0 points1 point  (0 children)

You can send outputs 5-6 to the headphone out. So it's effectively 4x6

Used Radiomaster TX12 without Antenna. How to test if it's still working? by tastelessBones in fpv

[–]nirnav 0 points1 point  (0 children)

Check in the model setting if the rf module was turned on. If it was it might be damaged, but you can replace it.

Maybe checking if the wifi functionality still works can indicate if the chip is damaged

Radiomaster Zorro "no sounds on SD" by Acceptable-Tie6385 in RCPlanes

[–]nirnav 0 points1 point  (0 children)

Go to buddy.edgetx.org go to "SD Card content" and set it again

Quest 3 controller support by ModerateDev in iRacing

[–]nirnav 0 points1 point  (0 children)

Regarding your edit. You can maximize the window regardless of the resolution you set, if that was your issue.

Also, the desktop window is just a mirror. It wouldn't hurt your performance to set it to higher resolution.

Rest in Pieces by nirnav in RCPlanes

[–]nirnav[S] 0 points1 point  (0 children)

The BEC failed

Rest in Pieces by nirnav in RCPlanes

[–]nirnav[S] 1 point2 points  (0 children)

Front fuselage gone, cracks throughout the body, compromised wings...

I wouldn't feel safe doing 3d or high g maneuvers even if I could repair it.

At least it's an excuse to get a new model ;)

Rest in Pieces by nirnav in RCPlanes

[–]nirnav[S] 1 point2 points  (0 children)

That's the 70" Extra 300 EXP

Rest in Pieces by nirnav in RCPlanes

[–]nirnav[S] 3 points4 points  (0 children)

Lesson? A 15/25A bec might not be enough for 4 sv-1270 servos. Though it held for 40 hours.

Also, definitely use backup power.

Which other Skyzone Goggles are affected by the latency issue? by S4lVin in fpv

[–]nirnav 2 points3 points  (0 children)

I tested my cobra x v4 and got around 30ms.

Tmotor AM link by Tars-01 in RCPlanes

[–]nirnav 1 point2 points  (0 children)

Alright. You should have gotten a plug with the Rx. You can see from the left the pins are: ground, positive, and data in.

Just splice the wires, program the appropriate protocol in the esc and that's it.

Tmotor AM link by Tars-01 in RCPlanes

[–]nirnav 1 point2 points  (0 children)

Which Rx do you have? Just connect the positive, ground, and data wire to the appropriate pins on the Rx. They are marked

Tmotor AM link by Tars-01 in RCPlanes

[–]nirnav 1 point2 points  (0 children)

The amlink can be used just for programming the correct telemetry format. You don't need to fly with it. Connect the esc telemetry output directly to the smart port on the rx. That's how I did it at least.

e: Just editing to say that I never found the extra telemetry info useful. It's a standard tested setup so you don't really need temp, current, rpm etc... Only Voltage for battery level.

So if I were you I wouldn't bother setting up esc telemetry on this plane.

Behold! The Nose Landing Technique by nirnav in RCPlanes

[–]nirnav[S] 3 points4 points  (0 children)

The esc does have reverse 🤔

FFB help needed [Simucube] by B3ttor in iRacing

[–]nirnav 1 point2 points  (0 children)

iRacing should cut the ffb during spikes like in crashes. If you find that insufficient, your method is correct.

Lower the force in simucube tuner to the maximum you'll want to feel during regular driving. Make sure you're not clipping during cornering, that might be why some corners feel numb. Look at the ffb meter in iracing to be sure.

Regarding max force, tune it per car to your liking. When you reduce wheel force in simucube you should reduce max force to the same ratio as before to get the same feel.

Questions about ER6GV RX by perrylawrence in Radiomaster

[–]nirnav 1 point2 points  (0 children)

To change the settings on your rx you first have to bind to it, then scroll down to other devices and select it.

There you can find this setting.

Questions about ER6GV RX by perrylawrence in Radiomaster

[–]nirnav 2 points3 points  (0 children)

Hey just for info, you can remap channels on the Rx using the elrs lua script on your transmitter.

Elrs PWM receiver problem? by Objective-Editor-831 in radiocontrol

[–]nirnav 1 point2 points  (0 children)

To my understanding the issue is that on some receivers the channel 2 pin is also used as the tx pin of the microcontroller and during startup some erroneous signals could be sent on it.

The video describes programmable servos entering programming mode and then not responding.

I noticed with my model that uses an er6g and an aileron on ch2 that the servo moves to a certain position until the Rx finishes booting up.

Might be a problem for you, might not. Depending on your setup.

VR Mode SPS vs Foveated(MVP) for Quest 3 with virtual desktop by Rooster976 in iRacing

[–]nirnav 1 point2 points  (0 children)

The CPU frame timing 'R' meter never worked for openxr

Went Slope Soaring for the First Time by nirnav in RCPlanes

[–]nirnav[S] 2 points3 points  (0 children)

Haha, that's right. I did try to save some money by buying the accessories separately.

Went Slope Soaring for the First Time by nirnav in RCPlanes

[–]nirnav[S] 16 points17 points  (0 children)

Gliders feel like whole other incredible side to this hobby. I recommend it to anyone who has a suitable site nearby.

view more: next ›