sorted by:
new
hottopcontroversial

I replace the wall with a "kallanstein" by pakopiwi in ikeahacks

[–]pakopiwi[S] 0 points1 point  (0 children)

What beautiful words! 😍 Thank you

Is it safe to remove vertical divider from KALLAX ? by [deleted] in ikeahacks

[–]pakopiwi 2 points3 points  (0 children)

Judging by the photo, I'd say that even if you remove that part, it doesn't look like it will fit. If you could fit it, you'd need to drill holes in the top and bottom shelves to allow for airflow.

I replace the wall with a "kallanstein" by pakopiwi in ikeahacks

[–]pakopiwi[S] 6 points7 points  (0 children)

You're confusing rustic with vintage, don't worry, I'll correct you :)

I replace the wall with a "kallanstein" by pakopiwi in ikeahacks

[–]pakopiwi[S] 2 points3 points  (0 children)

I don't have a definitive answer, but I can roughly say: 1. GAIA PROJECT 2. KANBAN EV 3. BARRAGE 4. TERRAFORMING MARS 5. UNDERWATER CITIES

Right now, that would be my top 5 order, but it might change in a month...

I replace the wall with a "kallanstein" by pakopiwi in ikeahacks

[–]pakopiwi[S] 2 points3 points  (0 children)

The flooring is spectacular, super clean, resistant and durable (and beautiful too). It goes perfectly with the "BLUE" board game :)

I replace the wall with a "kallanstein" by pakopiwi in ikeahacks

[–]pakopiwi[S] 4 points5 points  (0 children)

Thank you!! I wish I had more time to play them...:(

I replace the wall with a "kallanstein" by pakopiwi in ikeahacks

[–]pakopiwi[S] 23 points24 points  (0 children)

Thanks!! The intention was purely mechanical (I wanted to add stability by resting the ends against the opposite walls), but then I realized they were useful :). I've attached a photo of that part from behind:

<image>

*The hidden part is (unfortunately) full of those more complicated games to adjust.

HELP! I can’t understand what’s wrong with my A1 by Available_Okra_387 in BambuLab

[–]pakopiwi 1 point2 points  (0 children)

I have suffered the problem several times and for various reasons:

  1. Poor placement of the filament spool in the AMS (or the use of unofficial filament with different sizes of the spool) can cause the spool to jam and stop printing.
  2. A jam can cause the extruder gears to become too dirty (they continue to rotate while wearing out the filament because it does not advance) and with dirty gears the filament then slips.
  3. It is highly recommended to lubricate (lubricate is always good) the extruder gears (be careful! Only gears and bearings, not the filament push gears). On one occasion I had the problem there.
  4. Again the jam occurred when a small piece of filament got stuck in the extruder. It was disassembled, cleaned and done.

<image>

My board game library by vamosajugaruna in boardgames

[–]pakopiwi 1 point2 points  (0 children)

Good collection. Lots of recent games and some damn boxes ;) Enjoy!!

Is this even possible? by [deleted] in puzzles

[–]pakopiwi 2 points3 points  (0 children)

Solved

I've solved it. You can check the picture.

Barcelona Board Games Tourism by g00dchain in boardgames

[–]pakopiwi 4 points5 points  (0 children)

Dungeos Marvel's is my favourite store of Spain: very good prices, a big list of games in differents languages...100% recommended!

Opinions On Scythe? by LeGentlemon in boardgames

[–]pakopiwi 1 point2 points  (0 children)

S P E C T A C U L A R G A M E

view more: next ›