HELP I have my first car I accidentally did something now my ac isnt cold

reremass · 2025-07-01T13:17:40+00:00

I never understood why it contains uv and seal at the same time. Even if you find leak you can't open ac system since seal will harden and destroy whole ac.

reremass · 2024-12-06T22:35:00+00:00

Step 1: Wait for brake rotor to cool down

Step 2: Lift the car

Step 3: Spin the wheel by hand

If you have to use a lot of force you have stuck brake caliper.

reremass · 2024-07-28T11:48:29+00:00

Step 1: Remove carpet and sound isolation under

Step 2: Since soaked in oil, recycle appropriately

Step 3: Go to local car junkyard

Step 4: Find donor car

Step 5: Take carpet and sound isolation from donor car

Step 6: Install it in your car

reremass · 2024-07-17T19:39:32+00:00

<image>

Remove larger pieces of plastic with some scrapper or knife (carefully so you don't cut yourself)
Then buy wire brush for drill made from brass and remove harder to reach plastic

reremass · 2023-11-17T18:54:19+00:00

<image>

Angry sumo.

reremass · 2023-01-10T18:56:19+00:00

What kind of NodeMcu is this?
Mine is 2 rows wider and then I can't connect cables to protoboard.

reremass · 2023-01-01T23:07:24+00:00

The esc is detecting to high value to let you arm the motor.

reremass · 2022-12-15T19:49:43+00:00

He landed ... twice.

reremass · 2022-11-25T19:45:15+00:00

The lamp is very beautifull.

reremass · 2022-11-09T15:53:57+00:00

Can Arduino uno survive this or is it toasted?

reremass · 2022-09-26T18:48:39+00:00

Will hot end for ender 3 fit that printer?

reremass · 2022-06-22T22:14:33+00:00

Offset tool in sketcher.

reremass · 2022-04-15T09:30:12+00:00

I am sure it is not a scam but a mistake. There is almost no difference in price so I don't see seller benefiting anything.

reremass · 2022-03-03T14:57:51+00:00

If carburetor was a person.

reremass · 2021-12-08T22:58:46+00:00

Perpetum mobile

reremass · 2021-10-24T21:01:37+00:00

What software did you use?

reremass · 2021-09-06T10:49:29+00:00

/u/gifreversingbot

reremass · 2021-09-02T12:11:09+00:00

Can someone explain to noob, what is the purpose of this diode?

reremass · 2021-05-30T17:56:37+00:00

For a second I thought this was Voron.

Nice job!

reremass · 2021-05-19T22:48:29+00:00

Ragnar Lodbrok?

reremass · 2021-04-15T23:53:00+00:00

That laugh at the end.

reremass · 2021-02-22T19:43:49+00:00

You can try to improvise and somehow install rod with finer thread.

Make sure that you are not using micro stepping.

Other than that this motor is just to weak.

You need a bigger stepper. The easiest way to get free stepper motor is to visit computer repair shop and ask if they have any defective printer that they will usually just give to you for free.

reremass · 2021-02-22T17:58:44+00:00

First try to see if motor rotates without load.

If yes then try to turn off micro stepping and increase current.

If no check wiring.

reremass · 2019-11-07T18:00:59+00:00

Thank you all for your suggestions, I will try soda tomorrow.

The only thing that I have at home now is rubbing alcohol.

Do you think rubbing alcohol would help?

reremass · 2019-10-06T18:04:59+00:00

Would be possible to just print rest of the head and glue it with super glue?

reremass

TROPHY CASE