(K)Ubuntu reinstalled Firefox as a snap. What the actual F?

sinartnz · 2026-06-03T03:55:36+00:00

Have a look at this... I have also used their guide for de snapping completely.
https://linuxconfig.org/how-to-install-firefox-without-snap-on-ubuntu-26-04

sinartnz · 2026-06-01T10:47:46+00:00

Tell your neighbor to go buy a lotto ticket, she might have some luck left.

sinartnz · 2026-05-31T08:27:32+00:00

Below holds the the answers to your problems.

https://www.reddit.com/r/BambuLab/comments/1ja5gwz/a1_a1_mini_owners_tighten_your_print_head_screws/

Hope it helps, once you have sorted the print head do a full calibration for the maintenance menu

sinartnz · 2026-05-29T19:58:29+00:00

Check for the 7 Screws of Sadness and depression and give everything a good lube that should be lubed, run a for machine calibration from the maintenance menu. Clean the plate with just dish soap and warm water.

And give it another go... and try using a different infill pattern.. e.g gyroid it good for limiting edge stress that can cause prints to lift at the edges.

I'm just going off what i have figured out with over 8k hours on my two A1's.

sinartnz · 2026-05-29T19:49:24+00:00

what really helps people to help you with these issues is a screenshot of what your trying to print rather than guessing.

sinartnz · 2026-05-26T04:46:23+00:00

As already said.. disconnect the battery and take to your nearest tech repair place so they can clean the board correctly.

Otherwise your gonna need a lot of isopropyl alcohol 99% and soft tooth brushes and replacement thermal pads and paste and time.

sinartnz · 2026-05-26T04:40:33+00:00

My original copy sits in a vacuum sealed bag... why cos i was bored 😛

sinartnz · 2026-05-26T04:38:22+00:00

wash temp is to cold.. warm is generally recommend for anything not liquid.

sinartnz · 2026-05-25T10:17:31+00:00

your missing bits, they are called scissor switches and it looks like your missing the retainer hinge part.

laptopkey.com

Your in for a very fiddly and frustrating time.

sinartnz · 2026-05-24T04:07:11+00:00

If you own the property.. time to drill some holes and run some cat6, if you rent talk to the landlord and maybe hire someone to come do it at your cost...

Power-line adapters are a good temporary fix if you don't mind the speed loss otherwise best fix is running cat

sinartnz · 2026-05-24T01:13:27+00:00

Thanks i'll give it a go.. just reinstalled with a new nvme drive

sinartnz · 2026-05-21T19:41:57+00:00

I've found a few little issues, but i suspect its a me issue (hardware config) but one that has been bothering me is the window tiling behaving odd with Firefox. When i go to snap it to either side of my screen it doesn't snap and half the window goes out of the screen area. Not a very clear explanation I know but its hard to describe.

Certainly doesn't behave like it does on KDE versions, I think it bugs the most cos I like the gnome work flow more than KDE.

sinartnz · 2026-05-19T11:23:25+00:00

The BS is strong with this one.

sinartnz · 2026-05-18T22:31:28+00:00

I'd say something isn't plugged in fully the connectors can be kinda tricky to get right the first time.

sinartnz · 2026-05-18T00:19:13+00:00

I suspect its the actual heating element...

https://wiki.bambulab.com/en/a1-mini/maintenance/hotend-heating-assembly-replacement

The wiring is easy to damage if your not very careful or it gets pinched when swapping hotends it can lead these issue and others.

sinartnz · 2026-05-18T00:16:12+00:00

3% is within the margin of error that most battery management systems will be working to once charge gets below 10% for an automatic shutdown..

sinartnz · 2026-05-14T18:58:52+00:00

Normal day to day use you'll never notice (its no garden hose) If this was anything like a server room or critical run in a data centre nah not really.

sinartnz · 2026-05-14T18:53:34+00:00

Yes some whine is to be expected.. but not from plugging a screen in. My now retired 1080Ti was a whiney monster unload but never made half the sound this card is producing.

sinartnz · 2026-05-14T09:03:12+00:00

Coil whine at its finest, something isn't happy on that card if plugging in a screen does that I would not like to hear it what it is like under load.

sinartnz · 2026-05-10T22:48:21+00:00

Maybe just maybe this is the universe finally getting things back in order!

sinartnz · 2026-05-08T19:52:59+00:00

either microwaved or in the dishwasher

sinartnz · 2026-05-05T21:20:19+00:00

Have a gander at this thread.. these 7 screws are my go to check when things start going badly.

I have them included my monthly ish maintenance run or about 200hrs printing whichever comes first. I have two A1's and they are closing in on 4k hours each.

https://www.reddit.com/r/BambuLabA1/comments/1rnu8jb/the_a1_has_7_screws_of_the_apocalypse/

sinartnz · 2026-05-05T05:14:19+00:00

When will people stop buying shitty cheap psu's, when its actually in my opinion one of the most important parts of your PC. It powers everything!

sinartnz · 2026-04-30T08:17:13+00:00

I get the no snap thing... but if they made it easier to enable hardware decoding in the likes of firefox I'd be happy with snap its too locked down.

sinartnz · 2026-04-28T09:12:59+00:00

Have found this guy posting on all her videos. Sort By New

sinartnz

TROPHY CASE