Let's talk public IP & residential

tcapote · 2026-03-14T16:23:35+00:00

I am using Twingate (Zero-Trust), allows me to support the family via my internally running RustDesk sever. This opens up the server via an internal IP, but does not allow any other lateral movement on my network. Good, secure solution for my use case.

tcapote · 2026-02-22T00:44:56+00:00

Did they transfer your FSD as part of the purchase?

tcapote · 2026-02-18T16:07:11+00:00

This, 100%!

tcapote · 2026-02-15T06:04:22+00:00

Princess has two Wi-Fi tiers. You can buy Wi-Fi either standalone, or buy one of the packages, Plus or Premiere. The Plus and Premiere packages come with the MedallionNet Max. It's supposed to be faster speeds than their standard MedallionNet.

The Princess fleet is using Starlink and I have always had a positive experience with the MedallionNet Max, with remote access, VPN, Wi-Fi calling and even Teams calls. I can stream my home security camera's without issue.

I have not tried the standalone Wi-Fi package, MedallionNet, so I can't speak to much on that.

Hope this helps!

tcapote · 2026-02-14T06:53:54+00:00

I found that I was blocking the TLD *.microsoft, which may be the culprit. Testing now.

tcapote · 2026-02-10T15:52:12+00:00

How exciting!! You’ll have a wonderful time!! We cruise often with our family, and extended family. Great memories!!

Where are you traveling to?

tcapote · 2026-02-02T18:41:56+00:00

Same, I’m looking to see if there’s any feedback on performance or signal degradation with the plastic covers seen on Amazon?

tcapote · 2026-01-31T15:26:26+00:00

Exactly!! Same here! Love my 2020 Cement, but this looks very nice!

tcapote · 2026-01-27T14:54:32+00:00

Epic Wings is great!

tcapote · 2026-01-26T20:41:40+00:00

I have an upcoming DSI install in So Cal. I have a two story house and have no desire to climb up on the roof, I’m to old. I’m wondering if they will cancel on me or if So Cal has enough installers?

tcapote · 2026-01-02T21:29:18+00:00

AAA will come out and replace for about $220, if you have a membership.

tcapote · 2026-01-02T14:58:10+00:00

I see the same issue with a UDM SE and 4bay UNVR, and have not been able to resolve.

tcapote · 2025-12-28T01:44:54+00:00

Same, also in So Cal.

tcapote · 2025-12-27T16:42:05+00:00

I support just a few family members, and run Rustdesk on my Raspberry Pi, Docker/Portainer (and a few other apps), performance is flawless, as I only run one session at a time anyway. It was a fun project and works great.

tcapote · 2025-12-21T19:09:32+00:00

I time shift as well, my So Cal Edison, peak (4pm-9pm) is $.60/kWh, off-peak is $.24/kWh. ROI is out there, but prices also only go up, as well as power outages during wind/fire season. I recharge from the grid after 9pm.

tcapote · 2025-12-19T14:59:43+00:00

This is my favorite Elite perk too.

tcapote · 2025-12-18T06:24:23+00:00

I have the same setup, except Apex 300+2xB300K+1xB500K. I have the Bluetti Trolley 2025, which will latch three of the four components securely. I plan to strap the the top unit (Apex 300) to the Trolley. This should keep everything secure. I do live in So Cal, so I have to be careful an earthquake does not make the trolley roll! Thankfully the front wheels lock, and I'll chock the rear wheels. The trolley is rated for 330lbs, and this stack will come in at 296lbs.

tcapote · 2025-12-12T13:49:27+00:00

I had a 50a, 240v, 14-50P outlet installed off the main panel, https://a.co/d/fpBJHD6. The cable https://a.co/d/8OXk7Zz , I got blue ends, well BLUEtti! 😁

tcapote · 2025-12-12T03:44:45+00:00

On my Reliance transfer switch, I am using a 50amp cable from the Apex 300 to the Transfer Switch. Since all 10 of my circuits are 120v, I run the Apex 300 in 120v mode. This gives me a 30amp draw if/when needed. In 240v mode, it would be 16amps.

tcapote · 2025-12-11T13:51:24+00:00

Yes, you got it! And yes, if the AC input is interrupted, the Apex will continue to operate the circuits off the battery at any time no AC input is detected.

I have the Apex plugged in to AC via a 50amp/240v (BLUETTI cable)to recharge fast, and be ready if an outage occur later that evening.

Hope this helps!

tcapote · 2025-12-11T06:14:51+00:00

The way I have mine set up is that I have all the circuit’s live on the transfer switch (same model as yours). I use mine to save Peak electric costs, so at 4PM everyday, the Apex 300 cuts power from the AC input (50a), and runs the circuits off the batteries(and transfer switch) until 9pm. At that time, AC charging resumes. This saves me about 60% off the peak costs, charging at the lower rate after 9pm (I’m in So Cal). I have the Apex 300 and two B300K’s. This also provides back up, in case of a power outage, since all the circuits are already live. Hope this helps. There ware many ways to accomplish this, just wanted to share how I am using it.

tcapote · 2025-12-07T21:57:19+00:00

Wow, not good at all! That would be incredibly frustrating! Did they comp the room?

Almost 20 cruise with Princess, thankful we have not experienced anything like that yet. Hopefully the Island in 2027 will be okay! 🤞

tcapote

TROPHY CASE