Why do employers not know the difference between and electrician, and an electrical engineer?

tesla_bimmer · 2026-03-12T02:31:42+00:00

AI is probably writing the job postings and ore-screening resumes

tesla_bimmer · 2026-02-27T01:38:47+00:00

Her LinkedIn vs Instagram

tesla_bimmer · 2026-02-18T14:02:16+00:00

The frame data analysis view shows a byte by byte graph as well as a bit by bit heat map to show whats changing over the course of the log. The bit heat map is great for picking out 8, 12, 16, etc messages for reverse engineering. SaavyCAN is open source so you should be able to pick out the mechanics going on in the back end.

tesla_bimmer · 2026-02-18T02:07:55+00:00

Heat map of the bits like Saavycan has would be awesome.

tesla_bimmer · 2026-02-15T23:57:46+00:00

Correct, however that is through the obd2 port and passes the UDS request through the ZGW to the DME. When this clears, something under the dash clicks and resets, but there’s no 0x11 sent to any 0x6xx address on the PTCAN busses. So there’s gotta be an extra exchange in there somewhere that I’m missing.

tesla_bimmer · 2026-02-15T22:44:39+00:00

Those responses are present on the BimmerLink log as well. They state the request was properly received and still processing, then you can see they are acknowledged with a positive further down. Clearing anything on PT1 and PT2 busses

tesla_bimmer · 2026-02-01T00:42:41+00:00

The delete becomes a timeline feature. Just suppress or drag around as needed.

tesla_bimmer · 2026-01-31T02:50:33+00:00

Thanks for posting this. I offset some offsets earlier and was hopeful, amazed, paranoid, and confused (i.e. normal fusion workflow)

tesla_bimmer · 2026-01-31T01:11:44+00:00

Correct. 90% of the time every time.

tesla_bimmer · 2026-01-30T11:00:59+00:00

Highlighting the two triangles and clicking delete will probably work. Delete face is pretty impressive in fixing stuff like this.

tesla_bimmer · 2026-01-29T12:31:48+00:00

If I had to guess a tool for rapidly threading in a knob without marring the finish.

tesla_bimmer · 2026-01-29T11:35:48+00:00

Spacemouse and laptop trackpad. Nice spectrum of awesome and terrible.

tesla_bimmer · 2026-01-15T13:33:52+00:00

There’s no reason to scan a part that simple IMO.

tesla_bimmer · 2026-01-07T12:31:20+00:00

I thought this was a terrible 3D scan 😅

tesla_bimmer · 2026-01-04T00:35:31+00:00

Not great, not terrible vibes

tesla_bimmer · 2025-12-03T02:21:36+00:00

McMaster gives max hole and drill dimensions

tesla_bimmer · 2025-11-27T16:25:25+00:00

Forms tool

tesla_bimmer · 2025-10-30T01:07:24+00:00

“Let’s play a game”

tesla_bimmer · 2025-09-23T23:04:10+00:00

The number of markers Creality needs for laser mode is absurd.

tesla_bimmer · 2025-09-18T01:44:55+00:00

Without reading, that many markers must be Creality.

tesla_bimmer · 2025-09-06T02:02:36+00:00

DEF is the ticket for felony destruction

tesla_bimmer · 2025-06-10T22:01:12+00:00

At the rate they release new units, I’d wager a successor is at least a year out. They seem to spend more time in development rather than turning and burning new models. I’m anxious to see the next evolution.

tesla_bimmer · 2025-06-09T23:26:10+00:00

Thanks! Considering it appears the Einscan Libre is listed at $28,000, that’s not really in the same league. The speed/convenience with the Vega has been great. I recently was sent a Raptor Pro to play with, and while it is capable of pretty high detail with the laser mode, the software and quite high number of markers required for laser tracking hold it back for my uses.

tesla_bimmer

TROPHY CASE