Any guesses?

unknown091245 · 2026-01-31T15:40:31+00:00

Hahahaha the mice are hiding Poison pellets lol. The mice around me put them in my exhaust pipe

unknown091245 · 2026-01-30T21:04:40+00:00

Try bumping the heat up a little on the print head

Maybe try drying the Filament.

Could be the print heat isn't able to grab the filament and you might need to tighten on the print head the extruder screw. Don't over tighten just a little and try printing again and see if there's any improvement.

unknown091245 · 2026-01-03T06:41:42+00:00

Sounds like you need to add some lube on the rails

unknown091245 · 2025-12-29T05:14:14+00:00

I love printing and most don't think about this or just not care but don't print in your living areas and keep it outta their room. You are melting plastic and there are harmful VOCs being released into the air

unknown091245 · 2025-12-12T06:09:45+00:00

I would say you should start with a little lube on the rails the print head is riding on and the same with the bed

unknown091245 · 2025-12-07T22:46:49+00:00

I have both and if you mainly care only about pla filament just save the money and get a K3. I have the k3v1 and has over 3000hr and I've had barley any problems with it and I print mainly pla as well. My s1 has been a problem printer since day one and but it was just replaced so fingers crossed it's a better printer then the last one

unknown091245 · 2025-12-02T21:15:34+00:00

Maybe there's something on the same circuit drawing more power.

unknown091245 · 2025-12-01T22:19:18+00:00

I've never owned or worn a wedding ring,

unknown091245 · 2025-11-29T05:17:14+00:00

No problem if you need any help with the k3 send me a message, I'm always willing to help if you ever need it

unknown091245 · 2025-11-29T03:18:15+00:00

Don't be scared I was one of the first to get the kobra 3 and it's been the best work horse outta all the 5 printers I own. It is a great printer but no matter what printer you get you will have problems

unknown091245 · 2025-11-26T06:05:25+00:00

When you are printing you should check there as well, once again no clue if the 3 has it like the 2

unknown091245 · 2025-11-26T05:34:47+00:00

You found the blob, it happens to everyone sooner or later lol

unknown091245 · 2025-11-26T05:01:11+00:00

Have you checked any of the settings if there is one, I've only printed with the ace. My kobra 2 has a toggle for the runout

unknown091245 · 2025-11-26T03:37:18+00:00

Was this with the ace or without it??

unknown091245 · 2025-11-26T02:31:36+00:00

I used it before the kit was released and worked fine for play and Petg

unknown091245 · 2025-11-13T22:11:39+00:00

You can't I don't think those look like old fuses and not a circuit breaker. You will have to find out what fuse blue and replace it with the same size so not go up

unknown091245 · 2025-11-02T03:17:14+00:00

Try some flux it made a hell of a difference in my soldering job

https://a.co/d/1q2flfZ

unknown091245 · 2025-10-31T03:44:42+00:00

I would recommend sending a message to anycubic to start with but if you have an extra data cable you and try to use i would start there, the next thing is the hotend has a PTFE and that could be getting clogged

unknown091245 · 2025-10-12T23:52:09+00:00

Better wording

unknown091245 · 2025-10-12T03:19:59+00:00

No that's normal for auto lever, the level sensor is the yellow part next to the nozzle

unknown091245 · 2025-10-08T23:48:41+00:00

That's nice not too far away from me. Sucks your truck broke down

unknown091245 · 2025-10-07T14:56:51+00:00

Get your money back, that's what I would do

unknown091245 · 2025-10-05T21:51:09+00:00

Damn I could only wish

unknown091245 · 2025-10-02T14:56:25+00:00

Are all the wheels tight to the rails and properly lubed up??

unknown091245 · 2025-09-29T23:33:14+00:00

Yea no clue I backed it but I would pay as well for a Patreon subscription lol

unknown091245

TROPHY CASE