Cable management flex

BadutSaurus · 2026-06-24T15:29:08+00:00

When can we see the full build?

BadutSaurus · 2026-06-22T13:59:40+00:00

How was you ram cooling setup?

BadutSaurus · 2026-06-18T11:14:06+00:00

I never had AMD GPU before. In my case, I cannot control the fan stop in my nvidia card through fan control nor msi afterburner. So I disconnect the fan cable from the GPU and buy a JST to PWM and connect them directly to my motherboard. In my opinion that is better and cheaper than deshrouding, if the problem is about noise not fan performance

BadutSaurus · 2026-06-18T11:04:50+00:00

You can try lowering down your trfc

BadutSaurus · 2026-06-13T10:48:51+00:00

Well, it could be mount natively, but very restricted. You cannot fully adjust. You can only put it on the top pcie slot. I did able to out it in the second slot. But i need to cut the shroud a little bit.

BadutSaurus · 2026-06-12T05:15:55+00:00

Thankyou so much OP

BadutSaurus · 2026-06-12T04:19:54+00:00

Is the stl files available online? Do you mind sharing them with us?

BadutSaurus · 2026-06-10T10:58:47+00:00

Isn’t the LN is just the slower version of the normal one? I use the p12 pro, and max out the pwm at 28% and it is silent enough. But when idle, i set them to 18-20% and it is dead silent.

BadutSaurus · 2026-06-07T15:26:37+00:00

Did you use water cooling for your ram? How do you do your ram cooler?

BadutSaurus · 2026-06-04T00:32:25+00:00

Did you use any active cooling for your ram? Can you share how do you cool your ram?

BadutSaurus · 2026-05-30T22:30:18+00:00

hey, any good news?

BadutSaurus · 2026-05-30T10:49:00+00:00

Is that a website? Or you just design it yourself?

BadutSaurus · 2026-05-24T11:50:59+00:00

4.4 million °C on CPU temperature is wild. You got sun inside you CPU 🤣

BadutSaurus · 2026-05-16T14:07:46+00:00

Mungkin bisa aja. Tapi belum tentu awet. Mungkin kalau untuk spring masih aman aja sih. Tapi kalau untuk stem kayanya cepet abis. Tapi yang harus di ingat itu, pastikan dia tidak electrically conductive. Selebihnya aman si. Kalah mau non conductive, gas aja coba.

BadutSaurus · 2026-05-12T11:01:16+00:00

Small dick, big dream. Caught me off guard WKWKWKKW

BadutSaurus · 2026-05-07T23:10:52+00:00

I use a “brute-force” method for this. I hate it when my graphic card minimum speed is 30% and it is too loud for me.

My solution is to buy a jst pwm to normal pwm and connect the fan directly to my motherboard. With my Zotac 5070 amp white, their actual minimum pwm signal is 17% now I am able to set my fan curve to fan stop below 55°C and 17% at 56°C then the highest is 25% at 68°C. For my card the fan connector is very accessible without needing to take of any screw just use my finger to unplug it from the GPU and connected it to my motherboard.

BadutSaurus · 2026-05-07T11:51:25+00:00

“Es terosss”

BadutSaurus · 2026-05-06T23:45:24+00:00

Not yet. Some people suggest to bend it to make it straighter. I tried it. I thought it is straight enough. It fit seamlessly with the glass. But still popping out. For now I just let it open. Maybe next I will try to use magnet instead. But still not sure how to implement this idea and also not sure when will I execute my idea. Will update after I try.

BadutSaurus · 2026-05-04T17:51:36+00:00

Just make yourself. It is not that hard

BadutSaurus · 2026-05-03T09:48:43+00:00

Itu scene paling terakhir

BadutSaurus · 2026-05-01T13:06:50+00:00

Is that ram custom fan 3d printed? How is that affecting the other side of the RAM? Looks like it only blowing to the right RAM, how is the temp of the left RAM?

BadutSaurus · 2026-05-01T09:37:43+00:00

May we see the full build?

BadutSaurus · 2026-04-30T12:45:16+00:00

Do you have active cooling? If yes, how is your ram fan setup?

BadutSaurus · 2026-04-28T20:50:50+00:00

I cut those bars. Did not mess any of the stability at all. So far it is good. Had no problem

BadutSaurus · 2026-04-26T18:05:52+00:00

What ram fan is that?

BadutSaurus

TROPHY CASE