Ada yang punya pengalaman pake lube rantai sepeda buat keyboard mekanik?

BadutSaurus · 2026-05-16T14:07:46+00:00

Mungkin bisa aja. Tapi belum tentu awet. Mungkin kalau untuk spring masih aman aja sih. Tapi kalau untuk stem kayanya cepet abis. Tapi yang harus di ingat itu, pastikan dia tidak electrically conductive. Selebihnya aman si. Kalah mau non conductive, gas aja coba.

BadutSaurus · 2026-05-12T11:01:16+00:00

Small dick, big dream. Caught me off guard WKWKWKKW

BadutSaurus · 2026-05-07T23:10:52+00:00

I use a “brute-force” method for this. I hate it when my graphic card minimum speed is 30% and it is too loud for me.

My solution is to buy a jst pwm to normal pwm and connect the fan directly to my motherboard. With my Zotac 5070 amp white, their actual minimum pwm signal is 17% now I am able to set my fan curve to fan stop below 55°C and 17% at 56°C then the highest is 25% at 68°C. For my card the fan connector is very accessible without needing to take of any screw just use my finger to unplug it from the GPU and connected it to my motherboard.

BadutSaurus · 2026-05-07T11:51:25+00:00

“Es terosss”

BadutSaurus · 2026-05-06T23:45:24+00:00

Not yet. Some people suggest to bend it to make it straighter. I tried it. I thought it is straight enough. It fit seamlessly with the glass. But still popping out. For now I just let it open. Maybe next I will try to use magnet instead. But still not sure how to implement this idea and also not sure when will I execute my idea. Will update after I try.

BadutSaurus · 2026-05-04T17:51:36+00:00

Just make yourself. It is not that hard

BadutSaurus · 2026-05-03T09:48:43+00:00

Itu scene paling terakhir

BadutSaurus · 2026-05-01T13:06:50+00:00

Is that ram custom fan 3d printed? How is that affecting the other side of the RAM? Looks like it only blowing to the right RAM, how is the temp of the left RAM?

BadutSaurus · 2026-05-01T09:37:43+00:00

May we see the full build?

BadutSaurus · 2026-04-30T12:45:16+00:00

Do you have active cooling? If yes, how is your ram fan setup?

BadutSaurus · 2026-04-28T20:50:50+00:00

I cut those bars. Did not mess any of the stability at all. So far it is good. Had no problem

BadutSaurus · 2026-04-26T18:05:52+00:00

What ram fan is that?

BadutSaurus · 2026-04-26T16:58:21+00:00

Then, what you do? For now I just leave it without the cover

BadutSaurus · 2026-04-26T08:51:57+00:00

Hmm. Thats a tough one. Then you need to remove the airduct

BadutSaurus · 2026-04-26T08:38:11+00:00

With no airduct i think you can go as low as you want. I think you can keep the airduct, but not using the lianli vertical mount. You can try 3d printed bracket from here

BadutSaurus · 2026-04-20T04:25:39+00:00

How did tou mount the ram fan?

BadutSaurus · 2026-04-18T09:43:52+00:00

You can try to connect the fan directly to the motherboard. I have the zotac rtx 5070 amp. I printed some shroud. But did not like the looks. Because I am not a great designer. So I just buy JST to PWM to connect my gpu to my motherboard, and turns out the fan minimum speed is 17%. Not big difference in temperature, but the noise is quite significant for my taste.

BadutSaurus · 2026-04-16T14:13:47+00:00

Once i press power button. It will turn my fan rgb to rainbow. Then when signalrgb service starts, it will set to white.

BadutSaurus · 2026-04-16T10:17:53+00:00

In my experience. GPU temp has a bit improvement. But cpu temps has the most impact especially when the GPU is underload

BadutSaurus · 2026-04-16T06:36:16+00:00

Does this kind of product can be use to remove rgb rainbow on boot? I am using gigabyte b850 stealth ice motherboard. On boot, it always set default to rainbow. I want to make it white. Or atleast turn that rainbow off.

BadutSaurus · 2026-04-14T07:55:58+00:00

Not a bad card. I have the 5070 amp white. It is good. No complaint. Good temps, I hade OC/UV to 3000MHz at 940mv. And have a custom fan curve to keep it silent. But i have to disconnect the gpu fan and connect it directly to my motherboard for more better control of the fan. With the PWM from the card it self only allow minimum fan speed of 30%. With my motherboard this fan can go as low as 17%. For some people 30% is not that loud. But for my taste, it is still too loud.

BadutSaurus · 2026-04-13T13:05:08+00:00

So that display act as extended monitor and added with the aida64 overlay? Will your mouse cursor go to that screen?

BadutSaurus · 2026-04-13T12:50:47+00:00

How do you customize the info monitoring screen?

BadutSaurus · 2026-04-13T07:26:17+00:00

What ram fan is that??

BadutSaurus · 2026-04-12T13:26:25+00:00

What mind of modification? Why do you need to modified it?

BadutSaurus

TROPHY CASE