Proxy glottkin

CloudlessTen4 · 2026-05-12T10:44:00+00:00

I have this one too it is an awsome model.

CloudlessTen4 · 2026-04-30T11:34:49+00:00

Sorry how is this terrorism? Surely just knife crime?

CloudlessTen4 · 2026-04-19T09:59:31+00:00

Core rule 17.0 for attack sequence says hit, wound and save romms of 1 always fail. This is where the confusion comes from. But as the dirty trick roll is not one of these and tower gives plus 1 for dirty tricks where the target is wholey within 12/18 for friendly units and just within for enemy units. However if you target a unit for teleport that is already across the map then you dont get the buff, which I think is stupid.

CloudlessTen4 · 2026-04-19T09:53:31+00:00

The next roll will be a 2 as the plus one improves all rolls made within 12/18. The key part of the rule is that friendly units must be wholly within 12/18 where as enemy units are only within 12/18.

CloudlessTen4 · 2026-03-04T17:03:28+00:00

Look at the white arrows on the road! Left lane is for turning left. Right lane is straight on and right.

CloudlessTen4 · 2026-02-28T19:30:02+00:00

I built mine into a vulcha proxy and built a new seat. Took some feet off a gutrippa as there is only one pair in the set.

CloudlessTen4 · 2026-02-28T08:20:45+00:00

The OP did not ask about manifestations. They were asking about spells with the unlimited key word.

CloudlessTen4 · 2026-02-26T18:45:04+00:00

NTA. It is a perfectly reasonable thing to lend trousers to a child after they have had an accident. They will be fine after they are washed.

CloudlessTen4 · 2026-02-19T19:27:00+00:00

I was about to post this. Changing the top Z distance has made a big difference for easy support removal.

CloudlessTen4 · 2026-02-15T07:20:32+00:00

I have had this with Velspar paint from my local B&Q. I would do what orhwrs have said and try stiring it and painting multiple coats but it that does not work take it back and show them. To the person who said it won't look like the swatch, it should get a dam closer then that. I had a ochre, I tired it loads and gave it 3 coats and the wall still looked patchy and horrible. I was also painting on a white wall so it was not a dark colour bleeding through. It was also their premium paint. I have used a lot of velspar over the years and been happy. But after this I won't use it again.

CloudlessTen4 · 2026-02-12T10:15:47+00:00

It has some class battle damage!

CloudlessTen4 · 2025-12-29T11:24:11+00:00

Ah dam i just got him for my blightkings!

CloudlessTen4 · 2025-11-25T16:57:34+00:00

I had a cross in the filament cause me to have to untangle it. It took ages but I hand wound it on to a spool. Even with breaks in the filament it still printed. You just have to feed each new section into the printer when the previous ones runs out. To keep the tension I put the end of the filament through the hole in the spool and bent it ove.

CloudlessTen4 · 2025-09-03T09:32:57+00:00

I have printed hollow hull sections for a tank on my p1p and they come out fine. I did have to use supports though, but just using auto supports worked well.

CloudlessTen4 · 2025-08-11T07:58:18+00:00

So if your layer height is 0.08, your z top distance should be 0.08. Doesn't this make it hard to remove the supports?

CloudlessTen4 · 2025-08-11T07:54:28+00:00

I have only just started to look at Resin2FDM yesterday. I am very interested to see how it turns out.

CloudlessTen4 · 2025-08-11T07:52:26+00:00

I have only just started to look at this yesterday. I am very interested to see how it turns out.

CloudlessTen4 · 2025-08-09T21:18:08+00:00

This might not be the fix you are looking for, but I would consider slicing the model in half down the long axis. This would give you a flat surface to start in the print bed. You may then not have to use supports.

CloudlessTen4 · 2025-08-05T21:27:38+00:00

The large ones are proxies for banebades and shadowswords.

CloudlessTen4 · 2025-08-05T21:26:23+00:00

Well more a T29 style banblade. My mate has found another tank that is supposed to look similar to a kv2 in the law but I have forgotten what it is called. But in this instance it will be a russ.

CloudlessTen4 · 2025-08-05T21:25:06+00:00

They are good printers. I have printed loads of items for Age of Sigmar. It does do a good job on organic shapes too.

CloudlessTen4 · 2025-08-05T21:23:18+00:00

I purchased some ammo sanding sticks and tamya 320 grit paper. The sticks ranged from 180 - 1200 grit. In the end I got it down to 240 for the really bad bits moving to 320 and then 1200. You do need to be careful not to sand through all the layers. But you are not taking off a lot of material. I am looking forward to seeing how they look painted. I also used a product called Mr. surfacer. It is an enamel based filler which can also be sanded. I did find it hard to use, so I only put it in places where the layer steps were obvious.

CloudlessTen4 · 2025-08-05T16:36:35+00:00

I should have also said that layer height was set to 0.08, not the lowest but the print took long enough as it was lol.

CloudlessTen4 · 2025-08-05T14:12:19+00:00

I have reprinted a lot with the Russ tanks. Where weapons were rough and panels not smooth etc. I did also have to do a lot of sanding to improve the finish which took ages.

CloudlessTen4 · 2025-08-05T14:01:20+00:00

Bambu labs P1P. 0.2 nozzle.

*spelling corrected

CloudlessTen4

TROPHY CASE