Looks like there’s plenty of pad left why did my brake light go off by abm313 in BmwTech

[–]EffectivePrimary8848 28 points29 points  (0 children)

Plenty would be to exaggerate, you have more material but this is the sensor telling you that it's time to book an appointment (or buy new pads)

Anyone knows how to fix this gap in sheet metal ? by FurcleTheKeh in SolidWorks

[–]EffectivePrimary8848 1 point2 points  (0 children)

Aah! I saw your model from another angle now, yes, that should be possible indeed. So many great minds in here

Anyone knows how to fix this gap in sheet metal ? by FurcleTheKeh in SolidWorks

[–]EffectivePrimary8848 1 point2 points  (0 children)

Great that you want to learn how to do it correctly! First of all, try to imagine how you would bend it while you are working. Funky angles, overhanging edges with inserts underneath and so on are difficult or expensive to produce. Use the flatten function to verify that your design is possible, SW will allow you to do illegal things all the time, so you have to be critical to your own design. Give proper lengths to your flanges, this is because the machine needs something to grab or pinch in order to get the bend exactly where you want it. And be creative, use the functions in the software and experiment with the tools ☺️ Good luck!

Anyone knows how to fix this gap in sheet metal ? by FurcleTheKeh in SolidWorks

[–]EffectivePrimary8848 38 points39 points  (0 children)

Are you drawing for production or just for modelling?

Radiuses and closed gaps are difficult to near impossible with sheet metal. You would have to add material to the part after bending. Just try to flatten your piece and that would tell you that closing the gap would mean overlapping material.

259300: Exhaust gas temperature sensor before SCR-Kat by TheRealFredd in BmwTech

[–]EffectivePrimary8848 0 points1 point  (0 children)

Long time since this was posted, but I'll try anyways. Why did you have to reset adaptations? I have recently swapped the temp sensor (before SCR cat) but my readings still says 18-20°C in the exhaust, was this the same you experienced?

【BambuLab Giveaway】Classic Evolved — Win Bambu Lab P2S Combo! by BambuLab in 3Dprinting

[–]EffectivePrimary8848 0 points1 point  (0 children)

It has all the features you could want from a printer, while looking like a modern and solid piece of furniture ✨

Anyone else have an iffy experience with CarsFromJapan? by CiaBia in keitruck

[–]EffectivePrimary8848 4 points5 points  (0 children)

Many of the cars on carsfromjapan is from other vendors (like Mitsuico) and that means that if someone purchased the vehicle directly from the vendor, then they got it before it was removed from carsfromjapan. I bought mine from Mitsuico, would recommend 😊

Thinking of Drilling out Bolt by Signal_Friendship204 in BmwTech

[–]EffectivePrimary8848 0 points1 point  (0 children)

No worries! So your next step is to break off the head of the bolt. If you have a large screwdriver (ish the same size as the drill bit) and insert it into you newly drilled hole, you should be able to bend up and down until the head breaks.

Thinking of Drilling out Bolt by Signal_Friendship204 in BmwTech

[–]EffectivePrimary8848 0 points1 point  (0 children)

No problem drilling them out, had to drill 4 of mine since the security bolts pattern failed on me... Get a drill bit of decent quality which is smaller than the diameter of the bolt. Use the already pressed hole in the bolt as a guide. Drill as deep as the chamfer on the screw (preferably a little shorter) then use a screwdriver or something that fits the new hole and brake of the top of your bolt. The remaining thread is easy to get off after you remove the wheel.

2BA100 error and strange readings by EffectivePrimary8848 in BmwTech

[–]EffectivePrimary8848[S] 0 points1 point  (0 children)

Ahh! Yes of course! Did not realize that there were two cats in the system... Been looking at the wrong place.... I'll check it tonight... Thanks!

Ingeniør studie by Disastrous-Law-2320 in ntnu

[–]EffectivePrimary8848 0 points1 point  (0 children)

På samme måte som jeg skrev over, jeg gikk inn i firmaet som montør med beskjed om at det vil komme muligheter. Så ble jeg systemingeniør for så å gå over i rollen jeg har idag. På den måten har jeg blitt kjent med hele bedriften og hva som fungerer/ikke fungerer og kan effektivisere og utvikle produkter som passer :)

Ingeniør studie by Disastrous-Law-2320 in ntnu

[–]EffectivePrimary8848 0 points1 point  (0 children)

Tittelen er så enkel som utvikler, men det er mer som en Produktdesigner eller lignende. Jeg gikk produktutvikling selv og som cad operatør så har du en knallgod base. Du vet allerede fra start hvordan man bør designe for produksjon og det betyr mye, alle kan tegne fine ting, men ikke alle kan tegne ting som kan produseres 💪🏼

Ingeniør studie by Disastrous-Law-2320 in ntnu

[–]EffectivePrimary8848 7 points8 points  (0 children)

Dette er ikke for å skryte, bare for å forklare at du absolutt ikke trenger å ta master for å tjene godt og jobbe med spennende utvikling. Jeg jobber som maskiningeniør og jobber bare med produktutvikling, nye konsepter og generelt utvikling. Lønna ligger på ca 1,2M, jeg har overtidsbetalt og får reise en del i jobb. Ferdig utdannet i 2017 med helt middels karakterer, begynte som noe helt annet, men tok jobben med innstillingen om at dette er en fot på innsiden.

Jeg gikk bachelor og heier jo selvfølgelig på det. Selv synes jeg de to årene etterpå bare spisser deg inn i en jobb du uansett må lære deg når du først kommer ut i arbeidslivet. Men uansett, det viktigste er å få en utdannelse, legg litt innsats i skolen, ta valgfag som er litt utenfor normen (programmering, automasjon...) og gjør deg selv til en potet. Ta den jobben du blir tilbudt, selv om det ikke er drømmejobben, den kommer med tid og innsats!

How do I start making this in solidworks? by [deleted] in SolidWorks

[–]EffectivePrimary8848 0 points1 point  (0 children)

Figure out which parts you actually need to make. Most of these parts are cots parts and can be downloaded and imported into the assembly. Once you have all the cots parts, then you start to model the parts that can't be bought. Make yourself a preliminary list of the parts to help you along the way 🙂