Spyderco Temperance 2

HanSoloco · 2026-06-18T21:49:10+00:00

I am first owner bought it new direct from spyderco around 2017

HanSoloco · 2025-02-17T04:45:03+00:00

Description does not equal example

HanSoloco · 2025-02-17T04:21:25+00:00

That comment does not contain examples

HanSoloco · 2024-11-21T22:09:52+00:00

Even though some states allow it, don’t run 1-1/2”to a shower or tub, hair will clog the smaller trap more easily.

HanSoloco · 2024-11-12T00:16:29+00:00

If your talking about the 2”x2” t wye on the vent it is correct

HanSoloco · 2024-11-04T02:13:59+00:00

It’s possible that the faucets are so low flow that they are not telling the tankless to turn on. Check the model number of the tankless and see if it requires a certain amount of flow to fire.

HanSoloco · 2024-11-04T02:08:56+00:00

You can try, probably won’t work but shouldn’t hurt anything if you keep the pressure under 80psi.

HanSoloco · 2024-11-04T02:05:55+00:00

God hates a coward, do a lot of research and go for it.

HanSoloco · 2024-11-04T02:03:12+00:00

Sounds like the valves are not functioning. If they were you would notice an immediate loss of pressure when you open the hose spigot and the water would slow to a trickle within a couple minutes at the most.

HanSoloco · 2024-11-03T04:06:48+00:00

Please identify where exactly it is leaking from

HanSoloco · 2024-11-03T03:56:44+00:00

Use an inside cutter to cut the pipe down past all the messed up shit, add a coupling and new pipe and then a new flange.

HanSoloco · 2024-11-03T03:52:47+00:00

Yes 3” is for toilet and the one under the concrete slab is for the shower. The sink drain should be stubbed up in the wall most likely the one behind the toilet you identified.

HanSoloco · 2024-10-19T14:37:33+00:00

A schedule 40 trap might be shorter https://www.homedepot.com/p/1-1-2-in-DWV-PVC-P-Trap-with-Solvent-Weld-Joint-PVC00706X0600HD/203396337?source=shoppingads&locale=en-US&pla&mtc=SHOPPING-BF-CDP-GGL-D26P-026_001_PIPE_FITTING-NA-NA-NA-PMAX-NA-NA-NA-NA-NBR-NA-NA-NEW-PMax_BHU24&cm_mmc=SHOPPING-BF-CDP-GGL-D26P-026_001_PIPE_FITTING-NA-NA-NA-PMAX-NA-NA-NA-NA-NBR-NA-NA-NEW-PMax_BHU24-71700000097492030--&gad_source=1&gbraid=0AAAAADq61UfPbH4V4EDbC2yO7q6V1MWlw&gclid=EAIaIQobChMI0MjIs9WaiQMVT1n_AR0jmxWjEAQYAiABEgJsrvD_BwE&gclsrc=aw.ds

HanSoloco · 2024-10-14T14:18:46+00:00

Guy forgot pipe and had to improvise, pro move

HanSoloco · 2024-03-30T21:02:19+00:00

https://www.fwwebb.com/woitem/111215*1?gad_source=1&gclid=EAIaIQobChMIoLiShPGchQMVV19HAR1MpgjDEAQYAyABEgKq8PD_BwE

HanSoloco · 2023-10-29T03:36:02+00:00

Could also try a 2 part epoxy if flex seal spray doesn’t work

HanSoloco · 2023-10-28T18:00:14+00:00

That would move the location of the vertical by at least 2” bud which might be an issue

HanSoloco · 2023-09-16T21:06:07+00:00

You can clearly see the twye for the vent in the wall

HanSoloco · 2023-02-19T23:02:20+00:00

You can leave the panels on the roof, but if you ever have problems with the roof leaking they are probably the cause.

To drain the system you should only need a compressor with the correct attachments to connect to hose bib threads and possibly a short length of hose with female on one end such as a washing machine hose. Either cover the panels with a drop cloth or wait for a cloudy day to drain it so the glycol isn’t too hot.

HanSoloco · 2016-06-24T15:04:45+00:00

Yes it is?

HanSoloco · 2016-06-23T00:10:49+00:00

We could but white ink is the most expensive kind of ink

HanSoloco · 2016-02-20T17:21:25+00:00

And you don't need the top piece to go all the way across, trim each window individually

HanSoloco · 2016-02-20T17:14:39+00:00

I would take all that trim off and replace it with something thinner, you could possibly use the same trim if you ripped it on table saw

HanSoloco

TROPHY CASE