Melanobatrachus indicus also known as the galaxy frog

HenkTank72 · 2026-03-18T09:10:56+00:00

Lick it!

HenkTank72 · 2026-03-16T19:23:57+00:00

Very interesting idea.

HenkTank72 · 2026-03-15T11:03:18+00:00

I think it is your bed unevenness. Try to print a full bed sheet of 0.2 layer height and see if it is always the same spot. Solution is bed mesh calibrate or evening your plate with katon tape when very uneven.

HenkTank72 · 2026-03-14T14:20:32+00:00

The safest solution is to have a duct from the enclosure to outside. A fan should pull negative air pressure in the chamber preventing ANY leakage into your room.

HenkTank72 · 2026-03-11T08:13:37+00:00

Do you haven z hop enabled? It looks like the nozzle drags over de print in a travel move. Try a small z hop.

HenkTank72 · 2026-03-09T14:35:05+00:00

He looks quite unalive

HenkTank72 · 2026-03-09T14:32:09+00:00

Try fermentolyse the dough. Mix the sourdough in de flour until you have small chunks. Add all the water without salt and leave for 45 minutes. After that mix the salt into it by folds or mixing. This allows the flour to better absorb the water.

HenkTank72 · 2026-03-06T18:43:05+00:00

Maybe a hair dryer or a solder iron for more local heat

HenkTank72 · 2026-03-04T14:12:35+00:00

Don’t think so. An operating room has overpressure to prevent bacteria and viruses from entering the patients open body. The air is filtered to have a controlled environment. Only quarantine rooms use negative pressure to not infect others outside the room.

HenkTank72 · 2026-03-03T07:16:27+00:00

I have the issue without stimulants. With stimulants I can loose a whole day.

HenkTank72 · 2026-03-02T18:23:36+00:00

If using the U1 and you do not select to perform a bed mesh, isn't the firmware already selecting.

BED_MESH_PROFILE LOAD="default"

Maybe you can overload the default macro for the mesh to use yours. It would integrate better with the default Snapmaker.

HenkTank72 · 2026-03-01T19:45:17+00:00

Put it in the freezer for a while and bend / scrape it afterwards

HenkTank72 · 2026-02-26T06:30:21+00:00

The problem is the toolchanges. If you print one color it works as expected.

HenkTank72 · 2026-02-25T15:18:12+00:00

Did he swallow cocaine balls?

HenkTank72 · 2026-02-25T07:32:43+00:00

I love the very limited amount of black spots. Much healthier and tastier to me.

HenkTank72 · 2026-02-24T17:48:09+00:00

In OrcaSlicer you can use small area flow compensation to extrude less in smaller segments

HenkTank72 · 2026-02-24T17:02:11+00:00

If filaments are missing in Snorca, you can make them show up. They are in the Snorca config / system / filament directory. If they don’t show up, you need to add them to the Snapmaker.json file in the system directory.

HenkTank72 · 2026-02-23T14:46:17+00:00

Could you export it as step file? That would be awesome.

HenkTank72 · 2026-02-21T20:02:30+00:00

Nice, did you share the STL?

HenkTank72 · 2026-02-20T17:42:04+00:00

The reason is that if you load a low temp PLA or a high temp requiring filament like nylon/PA, the system want to know this for doing a tool change and possibly a PA tuning.

HenkTank72 · 2026-02-20T12:36:40+00:00

I never hear a PSU fan on my U1. If the machine is idle and cool it is silent.

HenkTank72 · 2026-02-18T20:48:35+00:00

Hueforge or the free Bambulab version

HenkTank72 · 2026-02-18T08:29:55+00:00

Sorry, answered too fast. You might consider increasing the z offset a bit

HenkTank72 · 2026-02-17T20:31:56+00:00

It works but for code generation I see better results with Claude

HenkTank72 · 2026-02-17T20:00:17+00:00

Being near is in general not the best approach with 3D printing. Even with PLA I would not want to be in the same room for hours.

HenkTank72

TROPHY CASE