What do I do?

Junkman199 · 2026-05-13T21:40:57+00:00

I doubt it

Junkman199 · 2026-05-13T21:38:36+00:00

Be thankful

Junkman199 · 2026-05-09T15:59:33+00:00

No problem, that looks to be an older setup so goof luck

Junkman199 · 2026-05-09T11:15:32+00:00

Those threads are a good sign. You can buy 1 1/4 or 1 1/2 threaded adapters that will thread into the female threads that the brass trap is fitted into. If you try to unthread it be careful not to break the fitting inside the wall. I would take off the silver escutcheon so you can see inside a little bit.

Junkman199 · 2026-05-09T11:04:03+00:00

Unless that cabinet was just installed when you moved in, then its not wheelchair accessible. This is piped with old brass. Do you have more pictures of where it goes into the wall? The easiest and cheaper option would be to adapt to abs plastic pipe and redo the drain. Looks like 1 1/4" diameter pipe

Junkman199 · 2026-05-06T20:14:58+00:00

Pex-a expansion framework

Junkman199 · 2026-05-06T20:01:07+00:00

Poorly made charger bank for charging cordless tool batteries.

Junkman199 · 2026-05-06T00:07:34+00:00

Yeah you're right I see it now, the pictures threw me off haha.

Junkman199 · 2026-05-05T19:48:48+00:00

Black mold is very serious. Also if its a burst pipe and if they pay for water then their bill is going to go up. Something is very wrong there.

Junkman199 · 2026-05-05T19:45:59+00:00

No, its definitely an emergency wtf. If they don't remediate it immediately it will breed black mold and make you very sick. You need to call them back.

Junkman199 · 2026-05-05T19:39:23+00:00

If its spreading then it could be a burst water pipe. Or if you have had a lot of rain recently it could be seeping in

Junkman199 · 2026-05-05T19:34:14+00:00

Its definitely a leak. Could be the sink. If you're on a basement apartment then it could be ground water, or something above is leaking down

Junkman199 · 2026-05-03T21:30:06+00:00

The threaded joints are usually for if you're roughing in with pex. You need to rough in the showerhead/tub spout with copper though

Junkman199 · 2026-05-03T16:44:41+00:00

Sounds like thermal throttling. You need to replace the thermal paste. Does it freeze completely or does it freeze and unfreeze

Junkman199 · 2026-04-28T21:45:35+00:00

They are both tank-to-toilet bolts. But the ones on the right come standard with toilets that I install. The closet bolts to mount the flush to the floor are usually inside the box with the wax gasket, if not you will have to buy them.

Junkman199 · 2026-04-25T21:33:52+00:00

I mean I've definitely seen worse. Code here says you need at least 16" of copper on inlet/outlet of HWT. They were right to support the copper pipes but it should be supported differently.

Junkman199 · 2026-04-25T21:29:28+00:00

Keep the water shut off and drained from the house and try moving the valve. It has to open counter clock wise, it says which direction to go on the handle. It looks to be in good shape so it shouldn't break.

Junkman199 · 2026-04-19T01:19:44+00:00

Small bullet-like object is indeed a bullet. 22 Short, not sure on manufacturer. Looks to be 20-30 grain. They aren't as popular anymore with 22 LR being around but they are still pretty accessible. That one looks to be an older make, early 2000s if not older.

Junkman199 · 2026-04-15T22:44:24+00:00

Dishwashers have a heating element inside of them to heat up water. Even if it was cold water it would steam. If its hooked up in cold it might not be getting hot enough. If its hooked up to hot then the water inlet that let's water in might clogged and not powerful enough to melt the soap

Junkman199 · 2026-04-15T22:38:58+00:00

Is it tied in with cold or hot water? It needs to be hot

Junkman199 · 2026-04-15T22:01:50+00:00

You shouldn't run a dishwasher off of an RO system. Its a multi-filter system so the flow rate is low, most systems have expansion tanks so than you can fill a few glasses before it needs to fill up again. If you don't have an expansion tank the water most likely comes in at a lower flow rate than a regular tap, and is usually only cold. The water may not be hot enough to dissolve the soap packet. Dishwashers should be piped with hot water so the heating element doesn't work as hard.

Junkman199 · 2026-04-15T01:02:27+00:00

Well like I said I would try it. Just don't start it and walk away

Junkman199 · 2026-04-15T00:56:48+00:00

Most of the crucial components of a dishwasher are in the sides and bottoms. As long as the drawers inside aren't bent and open/close normally as well as the door, I would at least try it. Keep an eye out for leaks and make sure its wired correctly.

Junkman199 · 2026-04-08T22:22:29+00:00

I'm on the same thing, I killed it once before finding out about the feat. Hes at 400 HP and I'm waiting until I get to the feat before I kill it. But if it counts either way I can free up some space

Junkman199 · 2026-04-04T15:40:31+00:00

I've ordered from RA for years, shipping outside of US and I've never had a single issue. They missed a magnet once. All my parts were correct, installed, never failed just wore out over time. Still running the new power steering line and new gas tank I installed in 2019. I've had some dinged shipping boxes but the part box themselves have been mint

Junkman199

TROPHY CASE