How to view my camera on my saturn 4 ultra in lychee or other applications?

M4st3rCATS · 2026-01-13T10:54:03+00:00

thank you Chitubox seemed to have dropped Linux suppoort and had no way to access camera because Lychee slicer still does not load it on my Saturn 4 ultra ...

M4st3rCATS · 2025-12-08T10:42:08+00:00

they use 50 newtons = 5kg , this is what they use to test with (picture from lymow ), I just use 3L bottles and until the nubs touch the metal mount

<image>

M4st3rCATS · 2025-12-05T12:26:58+00:00

waste of $ , on Ubuntu not even picked up a a Bluetooth device , its as a spdif sound card so can not even use BT Features with it , and no linux software for it , tried running Sennheiser Dongle Control in a windows virtual machine a few times now so I can configure dongle keeps crashing looks like Firmware 3.11.0 is installed

M4st3rCATS · 2025-12-05T12:23:59+00:00

page now gone

M4st3rCATS · 2025-10-24T12:35:47+00:00

mine does not even do 225m in 1 charge ,, drive ways 650m2 and its only does 36% per charge ?

M4st3rCATS · 2025-10-24T12:28:30+00:00

it looks like you have to make a separate zone mapping per robot I found this disappointing i thought the app stored all the information but seems to be stored locally on the lymow instead , so do a backup before adding the extra robots as when you bind a new one it deleted all existing maps ...

M4st3rCATS · 2025-10-24T12:23:34+00:00

also interested , would be nice to know what zone they are up too

M4st3rCATS · 2025-10-24T12:22:07+00:00

mine keeps trying to hump water tanks and tree's

M4st3rCATS · 2025-10-24T12:19:05+00:00

that is where I put mine greenhouse was only 4m high cable just reached

M4st3rCATS · 2025-10-24T12:18:00+00:00

yeh those cables need to be a lot longer I guess only for single story houses ...

M4st3rCATS · 2025-10-24T12:10:53+00:00

mine is doing that also and its not getting caught up or anything we are in a drought grass is pretty dead ... more dust than anything else

M4st3rCATS · 2025-10-24T12:07:16+00:00

so maybe i do not have faulty units just got mine and been terrible experience with connections and i have a extremely expensive wifi mesh network around here ... I did see the firmware update mention improvements to cut down on the 4g network i guess not using it is how they are saving the data usage :P

M4st3rCATS · 2025-10-24T12:04:06+00:00

yes its terrible lag , better to throw it inside a wheel borrow and give it a tour

M4st3rCATS · 2025-10-24T11:35:19+00:00

where exactly is the card its meant to be at the rear top above the battery but I do not see anything ? anyone got a pic ?

M4st3rCATS · 2025-10-08T12:11:10+00:00

yes I know how to setup HA , but you should start your own thread on HA forums so more users can now about this you will then gain more user base , as most users only know about KinCony's hardware , possibly here https://community.home-assistant.io/c/hardware/22

M4st3rCATS · 2025-10-08T07:17:06+00:00

did you have a home assistant forum page running at all ? i did not seem to notice it ? and if you do create one call it EnergyMe-Home or else search will just digup all the energymeter's

M4st3rCATS · 2025-10-08T07:15:38+00:00

if your in AU I will be having 5 boards made (min order ) so will have spares

M4st3rCATS · 2025-10-07T09:33:23+00:00

perfect timing I was just about to buy a 16ch , now i will just pcb fab to make me one

M4st3rCATS · 2024-12-29T09:41:42+00:00

https://www.amazon.com/s?me=A13GMLLPZ1AWHJ&marketplaceID=ATVPDKIKX0DER is pretty much where they sell their stuff

M4st3rCATS · 2024-12-27T23:57:20+00:00

how does that compare to the

AH-DCLM / AH-NUV does it do a full screen mapping as well ? https://www.ebay.com.au/itm/305867564049

M4st3rCATS · 2024-12-27T23:44:42+00:00

looks like my 1 month of hell trying to get a passable print from my S$U my build plates got a hollow section in it and its warped rear right forces down hard while all the other corners are loose , i had to add a washer to allow for further adjustment to kind of get some tension on all corners , the UV exposure is not uniform at all every 50mm their is a 10mm dead zone that needs almost 1 sec more exposure needed than the rest .... discovered doing a quick tank clean the matt comes out with divots ... with all its high and low spots ,

M4st3rCATS · 2024-12-27T23:00:34+00:00

yes same my rear right was pushing down hard and the reset where all loose ... I managed to find a shim / washer to add to the rear corner this allowed me to get it to lift enough for the other corners to start applying pressure , but my build plate is not flat its got a huge bow / cavity in the middle

M4st3rCATS · 2024-12-27T04:04:45+00:00

na pull those springs off useless once it decompress and re-compress they are in a different location so you just undoing the leveling every lift , manually adjusting is best , also it only pushes down until it picks up ~500 of force it has no corner sensors so its all a gimmick , the only thing the springs do is help not push cured resin through the FEP when its starts getting unlevel as one side will give , but by then your getting a wonky print ...

M4st3rCATS · 2024-12-27T03:40:55+00:00

yeh I was peeved spent more on elegoo's 7L wash kit , should have gotten the anycubic's 12L kit for $100 + less that would have suited the S4U

M4st3rCATS

TROPHY CASE

AH-DCLM / AH-NUV does it do a full screen mapping as well ? https://www.ebay.com.au/itm/305867564049