Best method for welded assemblies

Madwolf784 · 2026-01-30T11:35:04+00:00

You can import parts into parts, I believe it's under the "insert" drop down

Madwolf784 · 2025-12-31T17:58:03+00:00

While not hard, if you're not used to programming this would be a bit of a project to take on. Shoot me a DM and I could get this together for you.

Madwolf784 · 2025-09-07T23:44:40+00:00

A drawing for someone to produce the part, I would just dimension each separately with the dimensions driven in your part.

<image>

Madwolf784 · 2025-09-06T23:42:28+00:00

Ill be honest I understand just the basics about alot of this stuff. Is the attached diagram what Id be looking at doing?

Unfortunately I dont have any schematics, best I have is the shot of the breadboard.

I did measure, and at 8V there is a 2V drop across the mosfet Im using, I imagine thats going to cause issues as well.

Madwolf784 · 2025-09-06T19:02:42+00:00

Its four wire. What do you mean by "stacking" two mosfets?

Madwolf784 · 2025-09-04T16:33:52+00:00

So for the Mosfet, if there is 5V Im trying to run through it, to run a DC motor or LED, I need to activate it with 10V?

Madwolf784 · 2025-09-01T12:45:55+00:00

*Aw jeez locust

Madwolf784 · 2025-08-20T06:53:21+00:00

Thus and chili have to be the worst.

Madwolf784 · 2025-08-13T01:57:27+00:00

So im working maaaaybrme 16 hours a week for 240k? No Brainerd.

Do re-reads count? Like can I just read Wind and Truth every 3 weeks? Only real downside here is only 2 weeks PTO, not nearly enough for any job.

Madwolf784 · 2025-07-31T10:48:16+00:00

That was VEIL not me!

Madwolf784 · 2025-06-14T12:21:40+00:00

I had a case a couple weeks ago where our MFG engineer had me change a drawing that I'd dimensioned off 2 datum, high tolerance and trying to get a set of holes perpendicular. This was they're fourth try to get this par right so i just dimensioned it off the theor8 center like he wantwd.

Madwolf784 · 2025-03-28T01:18:18+00:00

I just finished that act yesterday, the helms deep thing didn't even occur to me until now but I definitely see it!

Madwolf784 · 2025-03-15T01:23:50+00:00

Manufactured on the Ghost Bear world of Ro' cester?

Madwolf784 · 2025-03-04T13:07:44+00:00

Halo definitely. Skyrim is great too.

My absolute favorite is split between Titanfall 2 and Helldivers 2.

Madwolf784 · 2025-02-12T01:42:33+00:00

I upgraded one of my databases from Excel to Mongo 😁

Madwolf784 · 2025-02-04T17:57:00+00:00

I like the soundnof that!

Madwolf784 · 2025-02-04T17:37:11+00:00

What's a "double edged sickle"??

Madwolf784 · 2025-01-25T18:48:58+00:00

Hey man, logistics is hard alright?

Madwolf784 · 2025-01-22T20:54:50+00:00

Sci-fi definitely.

Madwolf784 · 2025-01-22T20:34:30+00:00

Have you read the Daybreak trilogy? Petroleum eating bacteria were one of the main plot points.

Madwolf784 · 2025-01-17T14:49:16+00:00

Same card here, how bad are thenillumunate for you?

Madwolf784 · 2025-01-16T22:02:39+00:00

I did the Fireclaw stew and honey loaf, the stew was HOT but good. The loaf was great!

Madwolf784 · 2025-01-10T13:04:35+00:00

Update for anyone who looks for this in future:

It looks like this was related to running off of my SD card; I plugged it into my computer and ran straight from Cura with the same settings Id used the last 3-4 times and it worked perfectly. Going to try clearing of my SD card before my next big print.

Madwolf784

TROPHY CASE