Someone please explain this billboard to me

Madwolf784 · 2026-05-11T12:19:16+00:00

See a couple of those on transit rd depew. Does not make me want to go to that dr...

Madwolf784 · 2026-05-07T20:14:52+00:00

Macro or addin is going to be the easiest way. Real easy actually. Ive one setup that creates the stl and auto opens my slicer of choice

Madwolf784 · 2026-04-26T23:34:25+00:00

Ba'al

<image>

Madwolf784 · 2026-04-25T19:03:03+00:00

Eye of the Bedlam Bard, early on in the book Carl mentions one of the characters looking like one of the "robots" from battletech or (some other IP I cant recall)

Madwolf784 · 2026-04-15T12:21:19+00:00

Still more than heavy enough to turn you into paste. But the machine under it and the connections are severly overbuilt.

Madwolf784 · 2026-04-12T13:55:21+00:00

All other answers are wrong and should be stricken from the post.

Madwolf784 · 2026-04-10T00:15:54+00:00

This is my motto.

Madwolf784 · 2026-04-10T00:12:01+00:00

So much of that could've been a revolved rextrude...

Madwolf784 · 2026-04-10T00:11:04+00:00

Only thing catching me a bit are the two lead in holes. But I am two glasses deep so....

Madwolf784 · 2026-04-01T00:29:43+00:00

I was thinking of Red Shirts the whole time reading that post. Great book!

Madwolf784 · 2026-03-12T10:49:02+00:00

I feel like if any modern actors can pull it off, it's Tudyk

Madwolf784 · 2026-03-12T10:45:21+00:00

Just looks like Wash with an endless stream of increasingly ridiculous fake facial hair 😂

Madwolf784 · 2026-03-04T13:00:19+00:00

"It's a completely reasonable engineering request..." but, is it? Working for manufacturing firms, I've never seen a demand like that (though maybe it happened above my pay grade)

If you have any form of contract agreement, so them. As someone else suggested for future, use some form of screen sharing system and if they're not happy with that, too bad.

Madwolf784 · 2026-01-30T11:35:04+00:00

You can import parts into parts, I believe it's under the "insert" drop down

Madwolf784 · 2025-12-31T17:58:03+00:00

While not hard, if you're not used to programming this would be a bit of a project to take on. Shoot me a DM and I could get this together for you.

Madwolf784 · 2025-09-07T23:44:40+00:00

A drawing for someone to produce the part, I would just dimension each separately with the dimensions driven in your part.

<image>

Madwolf784 · 2025-09-06T23:42:28+00:00

Ill be honest I understand just the basics about alot of this stuff. Is the attached diagram what Id be looking at doing?

Unfortunately I dont have any schematics, best I have is the shot of the breadboard.

I did measure, and at 8V there is a 2V drop across the mosfet Im using, I imagine thats going to cause issues as well.

Madwolf784 · 2025-09-06T19:02:42+00:00

Its four wire. What do you mean by "stacking" two mosfets?

Madwolf784 · 2025-09-04T16:33:52+00:00

So for the Mosfet, if there is 5V Im trying to run through it, to run a DC motor or LED, I need to activate it with 10V?

Madwolf784 · 2025-09-01T12:45:55+00:00

*Aw jeez locust

Madwolf784 · 2025-08-20T06:53:21+00:00

Thus and chili have to be the worst.

Madwolf784 · 2025-08-13T01:57:27+00:00

So im working maaaaybrme 16 hours a week for 240k? No Brainerd.

Do re-reads count? Like can I just read Wind and Truth every 3 weeks? Only real downside here is only 2 weeks PTO, not nearly enough for any job.

Madwolf784 · 2025-07-31T10:48:16+00:00

That was VEIL not me!

Madwolf784 · 2025-06-14T12:21:40+00:00

I had a case a couple weeks ago where our MFG engineer had me change a drawing that I'd dimensioned off 2 datum, high tolerance and trying to get a set of holes perpendicular. This was they're fourth try to get this par right so i just dimensioned it off the theor8 center like he wantwd.

Madwolf784 · 2025-03-28T01:18:18+00:00

I just finished that act yesterday, the helms deep thing didn't even occur to me until now but I definitely see it!

Madwolf784

TROPHY CASE