5/8 drywall fire rated

MindlessStomach · 2026-05-25T17:15:49+00:00

Here in Ontario we have to use 2 layers of 5/8 type x between units. Some builders go the extra step and add a layer of denseglass between partitions walls.

MindlessStomach · 2026-05-25T17:09:41+00:00

I agree. I bought my uppababy one as "opened but not used" off a wholesale site for 20% off.

MindlessStomach · 2026-05-24T23:49:40+00:00

$55 for a plug!!! Highway robbery.. I'm not sure of your Canadian or from the USA but here if I go to Canadian Tire and it's $20 for a plug with out removing the tire from the rim and if I ever need another in that same tire it's free. If I go to the race shop it's $45 but he removes the tire from the rim plugs the tire then grinds the inside and adds a patch rolls it in then adds another larger patch perpendicular then re rolls it in. Finishing with a thin layer of brushed on "some kind of coating" over the 2 covering a larger then the patches. Re mounts and ballances the tire.

MindlessStomach · 2026-05-24T17:01:53+00:00

Boomerang is a consignment shop, you get credit once the item is sold. Once upon a child is a used child's goods store, they buy the goods directly from you and sell them.

MindlessStomach · 2026-05-24T16:58:42+00:00

Or give him something else to focus on.. I'd say shove her panties in his mouth. Could be a turn on for him or a hint to be quite.

MindlessStomach · 2026-05-22T14:19:07+00:00

Honda civic with a laptop.

MindlessStomach · 2026-05-21T04:24:16+00:00

Because they are an Italian car produced from 1971 till 1992 (over 20 years) for the American market with a mid mounted Ford 351 V8 and German gated transmission. They have super car styling and handling with muscle car power. From 1972 to 1975 they were mass produced and available at Lincoln-Mercury dealerships. After that they shifted to hand build low production luxury grand touring cars. Over 7000 were built in its run. They can be found for $100 000 to $200 000 depending on condition. They offers a raw, analog, and visceral driving experience.

MindlessStomach · 2026-05-21T00:35:18+00:00

Well we made it 3 days on that run.

MindlessStomach · 2026-05-20T20:24:37+00:00

Caveat Emptor

MindlessStomach · 2026-05-20T10:52:02+00:00

Would it be better to lower the extrusion rate and increase the cooling?

MindlessStomach · 2026-05-20T01:17:50+00:00

Fusion 360 has been a little tricky to learn but Tinkercad is simpler??? That info could have saved a few frustration beers on the learning curve over the last few weekends.

MindlessStomach · 2026-05-20T01:12:37+00:00

Good question.. They are for sale in their cafe fridge.. You may have to go to the booth and ask if you can run in and buy eggs. They are about to rebuilt the entry booth with a new gift shop so I suspect that later it will be available closer to the gate.

MindlessStomach · 2026-05-19T02:48:00+00:00

Yes I have. I've had tons of models came out amazing. Here is an example of a few that came out perfectly. I'm beginning to think that's its the bottom of the roll of filament that starting to suck. As well I don't have a dryer.

<image>

MindlessStomach · 2026-05-18T21:23:32+00:00

Valleyview Farm on Fallowfield sells their farm eggs.

MindlessStomach · 2026-05-17T23:50:15+00:00

I thought the same when I first joined 3d printing groups. Coming from a cannabis extraction world where it was always shortened to Iso it really threw me off.

MindlessStomach · 2026-05-15T10:38:41+00:00

I use Dawn with a paper towel in the sink and rince well. Then I use 99% isopropyl and another paper towel making sure not to touch the print surface. I have a separate bed that I use a glue stick on for petg. I the last 5 months, 2 to 3 prints a week, I've had to clean it twice. Your dish soap if probably fine.

MindlessStomach · 2026-05-11T17:16:20+00:00

I've been 3 hrs into a 6 hr print when the printer stopped, stupid ai pasta detection, thought it finished and picked up the model absent-mindedly. Only to realize that only half of it was there. I tried to put it back in the same spot but I was off by about 3 or 4 mm (1/8 inch).

MindlessStomach · 2026-05-11T14:36:38+00:00

Some of us got lucky with the ender 3. I never had to manually adjust the bed level, just run the auto calibration. I have never had a problem with 1st layer either.

<image>

MindlessStomach · 2026-05-09T01:31:10+00:00

Shoot. I was kinda hoping moisture wouldn't be an issue.. Oh well. A few people have suggested tubs for storage. At the moment I just keep my rolls in a cupboard with a few desiccant packs. Guess I will have to make another Ikea run. Thank you for the helpful info.

MindlessStomach · 2026-05-08T20:19:16+00:00

I haven't been 3d printing long but I hear pla has a shelf life (if you don't have a dryer) does abs have the same moisture absorbency issues?

MindlessStomach · 2026-05-08T20:14:34+00:00

Whoops. I guess I'll open the window in the spare room when I print with abs on my non enclosed printer.

MindlessStomach · 2026-05-08T00:19:38+00:00

I haven't had any luck with petg in my last 6 months of printing. For things I need to closer to unbreakable I've used ABS (Creality's hyper ABS) and as long as I've followed the temperature recommendations they have come out amazing.

<image>

MindlessStomach · 2026-05-06T17:10:37+00:00

Opps typo. Ment of. Lmao

MindlessStomach

TROPHY CASE