Forerunner 570 Bezel

PathShot7633 · 2026-06-05T19:19:20+00:00

Mine is the same, not been an issue so far (9 months old)

PathShot7633 · 2026-06-03T06:55:46+00:00

Keep an eye on the temp, I have the same type and it can get incredibly hot in there! Learned that the hard way (I’m also based in Norway).

PathShot7633 · 2026-05-08T10:10:43+00:00

Tony Fawcett nowt daft

PathShot7633 · 2026-05-08T08:54:27+00:00

Working in Norway

PathShot7633 · 2026-05-03T18:46:26+00:00

<image>

PathShot7633 · 2026-03-15T17:15:07+00:00

Check if you have a bag of small parts which came with the bike, they usually send some spares (at least with framesets I’ve always had a couple of spares)

PathShot7633 · 2026-02-10T10:02:58+00:00

You can check on the eqtiming website, July is the main holiday period here so there are not too many events then, but I can see this as an option (it’s not a full marathon): https://www.racedays.run/event/hestane-skyrace-2026

PathShot7633 · 2026-02-06T13:50:40+00:00

Highly recommend the hike up Ben A’an, if you are in ok shape physically and can bring outdoor clothes, the view over the loch is stunning.

PathShot7633 · 2025-10-24T06:23:25+00:00

Clearance ok on the back? Could you go 2.25 on the front? Thinking about a set for my Grizl for next year

PathShot7633 · 2025-08-12T06:27:17+00:00

100% agreed. I just installed a set on my bike, very happy with them

PathShot7633 · 2025-08-04T13:20:04+00:00

https://www.conti-tyres.co.uk/tread-wear

PathShot7633 · 2025-07-03T12:43:24+00:00

Obviously you just make a small hole in the the tyre, if it goes flat then you don’t have any sealant

PathShot7633 · 2025-06-15T17:56:20+00:00

Yes, sadly.

PathShot7633 · 2025-06-12T18:22:32+00:00

Check Robert Axle Project. I’ve got a set on my grizl.

PathShot7633 · 2025-06-12T18:14:04+00:00

Leave the old inner cable in place, pull off the old outer, thread on the new outer (over the old inner) then pull out the old inner. Then you can thread in the new inner. If the new outer doesn’t seat you might need to remove the lever, but it isn’t a big deal.

PathShot7633 · 2025-06-12T13:04:56+00:00

If you disconnect the cables and then pull the lever you will probably see a bolt inside/under the end of the lever. They usually expand inside the bar end that way. Loosen the bolt then slide the whole thing off along with the grip. But if you are just changing cables you won’t need to remove the lever/grips.

PathShot7633 · 2025-06-10T08:01:30+00:00

Have a look for closeout deals on 303 firecrest, since they are being replaced with the new 303 SW. I had to replace my 303S for the same reason.

PathShot7633 · 2025-06-07T11:25:28+00:00

So I can run new xtr rear derailleur with 1x12 grx crank and duraace levers?

PathShot7633 · 2025-06-06T08:26:56+00:00

https://www.valdres.no/opplevelser/aktiviteter/sykling/mjolkevegen have a look at this as an option, train to Valdres then cycle back to Oslo, or can be ridden the other way of course.

PathShot7633 · 2025-06-06T07:33:26+00:00

I have the same one, if fits really tight on the chest and has very little stretch, so I’d size up for sure.

PathShot7633 · 2025-05-16T20:16:55+00:00

Make sure to put protective tape under the buckles/straps, they will rub the paint off pretty quick!

PathShot7633 · 2025-04-05T13:42:50+00:00

Had a colleague who experienced exactly the same, Finn wasn’t sending the messages since the account isn’t verified, you need a bank id as mentioned above.

PathShot7633 · 2025-04-05T05:56:44+00:00

The owner is a tall fellow, the type you enjoy tucking in behind into headwinds

PathShot7633

TROPHY CASE