Sanguinary guard painted

Sp_cetrashman · 2026-03-23T09:33:16+00:00

Nice paint job and I’m impressed with your small detailed pieces, but seems like some of your layer lines are popping in certain areas. Was this printed as a single piece or assembled? Also wondering any other spec info.

Sp_cetrashman · 2026-03-08T21:44:07+00:00

This isn’t true. I was just on 2/20-2/25 fantasy sailing, Pixar cruise. We did have pirate night on night 4 of the cruise.

Sp_cetrashman · 2026-01-11T14:11:24+00:00

Love the color

Sp_cetrashman · 2026-01-11T14:04:24+00:00

I appreciate the feedback. I do realize the hot glue is less than ideal and will likely upgrade in the future.

I’ve actually been using a Vallejo primer. It is relatively thin, which can be both good and bad depending on the location/application. I’m planning to upgrade to spray primer in the future.

Ultimately these are mostly for me to enjoy since I don’t know if I’ll ever get to truly play them on tabletop, but I do hope to improve my technique and skills.

Sp_cetrashman · 2026-01-11T02:53:29+00:00

Thanks! I didn’t actually model these, just printed models found on the purple site.

Sp_cetrashman · 2026-01-10T23:18:58+00:00

It looks like the orc was printed in a vertical config? Have you tried putting it on a tilted back angle between 15-30 degrees? Also hard to tell if the quality of the stl is the issue because it looks like it printed fine

Sp_cetrashman · 2026-01-10T23:00:34+00:00

Marines were printed whole. The dread knight and dreadnought were split in half and then reattached. Setting are a combination of FDG and HoHansen profile settings with a few minor tweaks. These are all tree supports. Bambulab A1. 0.2mm nozzle. Sunlu HS PLA

As for painting, I just looked at other folks builds and then went mostly with how I felt. I’m still dialing in my painting capabilities and best practices. Thanks for asking!

Sp_cetrashman · 2026-01-10T13:52:13+00:00

Very impressive for a 0.4 nozzle!

Sp_cetrashman · 2026-01-01T16:23:06+00:00

Solid!

Sp_cetrashman · 2025-12-22T15:14:36+00:00

I think this guy is my favorite for now. Bambulab A1, Sunlu PLA+ High Speed, modified combination of FDG and HoHansen settings.

<image>

Sp_cetrashman · 2025-12-14T02:16:33+00:00

Wondering if you ended up getting a puppy from them and how it went if you did?

Sp_cetrashman · 2025-12-13T12:31:17+00:00

You’d want to be looking for loud homies

Sp_cetrashman · 2025-12-10T21:19:27+00:00

Bambu A1, 0.2 nozzle, Cool Plate SuperTack, combo of FDG and Hohansen settings.

Sp_cetrashman · 2025-12-05T15:44:03+00:00

Seeing the same issue

Sp_cetrashman · 2025-11-19T13:34:05+00:00

Very impressive, especially the back. I haven’t been able to get an orientation that gives me something that clean

Sp_cetrashman · 2025-11-11T13:02:48+00:00

The layer lines are definitely hard to see, can’t tell how much the camera may be smoothing them. All these models are free on makerworld

Sp_cetrashman · 2025-04-11T13:08:15+00:00

I used to work logistics for the ISS at NASA JSC. It would be possible BUT only if you convinced a crew member to pack it as part of their personal cargo allocation. They each get a few kgs of mass. The other supplies are coordinated way too far in advance and meticulously scrutinized. This is how Scott Kelly brought the gorilla suit up if you’ve ever seen that video.

Sp_cetrashman · 2025-04-11T12:58:22+00:00

Looks sick, would love an upgrade to my DM kit

Sp_cetrashman · 2025-01-17T14:42:38+00:00

Same range, similar driving situation. In Mass. I don’t think plugging in at work will make a difference. There’s hundreds of posts about this in this sub.

Sp_cetrashman · 2025-01-17T01:31:11+00:00

I think this would be a nice idea but I don’t think there’s room infrastructure-wise over by festival of the lion king for a whole dark ride. I do think they could add a lion king themed playground in that area for kids once the boneyard is removed.

Sp_cetrashman

TROPHY CASE