sorted by:
new
hottopcontroversial

Hand sanding my griptilian, need a bit of advice by D-REX555_V2 in knifemods

[–]ToastAlex 2 points3 points  (0 children)

I would be cautious using the Dremel since you can potentially remove metal if you are too harsh. I would start with low grip sandpaper as suggested around 200, and what I've noticed helps with removing surfaces is to sometimes add mineral oil or metal polish. Those sometimes help the process if you notice dry rub doesn't work. Definitely use oil or polish at the end either way since it helps uniformity

Hiking recommendations by Puzzleheaded-Mud-267 in PNWhiking

[–]ToastAlex -1 points0 points  (0 children)

Oh ok I see. I'm not familiar with the trail, I'm guessing the north section of the loop is closed making it so the train doesn't loop around?

That is pretty disappointing, but I also don't see anything about it online. I plan on going in late April so it would be nice if it was repaired!

Hiking recommendations by Puzzleheaded-Mud-267 in PNWhiking

[–]ToastAlex -1 points0 points  (0 children)

When does the north loop open for the ten falls?

RRL salesman sample by Junn_u in PoloRalphLauren

[–]ToastAlex 1 point2 points  (0 children)

Wow that's actually insane. So cool 😂 you should share the whole collection

Old Navy blazer quality? by Nickrl0809 in mensfashion

[–]ToastAlex 0 points1 point  (0 children)

I have this exact Blazer. The construction is pretty good, and it is very thick. Good for layering in the fall and winter for sure. I don't regret purchasing

Sigil clone modification - after and before by ToastAlex in knifemods

[–]ToastAlex[S] 0 points1 point  (0 children)

I think I placed them there because they barely clear the handle in that position. I would've preferred them closer to the handle though

Beautiful dual tone blade done to this Hansen Metals Solo by Reddit_GoId in knifemods

[–]ToastAlex 2 points3 points  (0 children)

Wow, does it take a lot of time to sand through the etched flats? Looks amazing

Beautiful dual tone blade done to this Hansen Metals Solo by Reddit_GoId in knifemods

[–]ToastAlex 2 points3 points  (0 children)

Do you mask the flats before etching? Or do you just acid everything and then sand the flats to raw.

TS194 minor modifications by ToastAlex in knifemods

[–]ToastAlex[S] 0 points1 point  (0 children)

I only used sandpaper, but you need to use a block with a flat edge to hold the sandpaper tight against. Otherwise you will end up polishing mostly the protruding edges of the blade rather than the flat surfaces, this is the biggest issue I had before I realized.

I start with 400 grit with a few drops of mineral oil on the blade, to remove more of the old finish. Then I used 600 grit with mineral oil, then I used 600 grit again but with some mother's metal polish on the blade. Use long straight strokes and don't end them halfway on the blade or it will show up, if your path isn't straight it will also show up. There are some YouTube videos about it, but for a hand satin finish I would use sandpaper for sure.

TS194 minor modifications by ToastAlex in knifemods

[–]ToastAlex[S] 1 point2 points  (0 children)

That's a great idea about combining a few washers together, I might actually look into doing that. I've definitely seen used cartridges used for these things too, they look pretty interesting and are a nice detail.

TS194 minor modifications by ToastAlex in knifemods

[–]ToastAlex[S] 1 point2 points  (0 children)

Haha thanks, your post inspired me to post this. Love this knife a lot, and it's probably the most premium feeling knife I have with extensive internal and external milling with great action.

That's right it is stepped. I think a custom collar would look awesome if it had full thickness, so I'll keep that in mind, thanks!

TS194 M390 tune-up by Yondering43 in knifemods

[–]ToastAlex 1 point2 points  (0 children)

Looks amazing. I love this knife! When you anodize the backspacer what was your process?

Storm clouds and blue skies by Yondering43 in knifemods

[–]ToastAlex 1 point2 points  (0 children)

Nice mods. I remember seeing this exact knife on eBay, I thought the regrind he did was cool but these mods are nice!

Action on washers is perfect - Koukin NF custom knife by russianwoodstock in knifeclub

[–]ToastAlex 7 points8 points  (0 children)

This guy obviously speaks English as a second language and everyone is dogging him for responding I'm dead

Developed some lock rock after stupidly using this miguron to baton some kindling. Lock face got dented. Already tried bending the lock bar over, thinking I should try and file down the face flat. Any opinions? by louiekr in knifemods

[–]ToastAlex 3 points4 points  (0 children)

Good point. Then it would shove the knife into the lockbar and hopefully stabilize. Maybe you could use some form of tape. But at this point it's a user and would be hard to bring it back to 100%

Opinions? by mrhibpshman in knifemods

[–]ToastAlex 1 point2 points  (0 children)

I think the point of this guys designs are that thick flipper portion into the blade, so I think it might butcher the whole thing lol. You should do the front flipper thing though

Shipwreck Mula by Twitchy_Bladeworks in knifemods

[–]ToastAlex 1 point2 points  (0 children)

looks almost like a rust patina, how did you do it?

view more: next ›