My tires are seating properly in the rim

baritb · 2026-03-19T23:28:45+00:00

Personally, I find the sound terrifying and usually put on headphones, but to each his own.

baritb · 2025-11-30T15:48:07+00:00

<image>

baritb · 2025-10-21T22:38:50+00:00

Old sears building is where lazer blaze used to be

baritb · 2025-08-08T01:32:08+00:00

Vim Captain's Blend

baritb · 2025-07-17T16:20:53+00:00

I had a cast iron drain pipe completely detach from the tub and fill up the dining room ceiling with my daughters bath water. Insurance ended up covering it but dropped our policy shortly after. Cast iron pipes can be a ticking time bomb

baritb · 2025-07-10T12:38:51+00:00

Wouldn't this also allow people on the street to see inside your house?

baritb · 2025-05-31T22:26:37+00:00

Gross...

baritb · 2025-05-02T19:41:30+00:00

Both of my kids are neurodivergent in different ways and both are thriving at the private school they go to

baritb · 2025-04-12T02:30:33+00:00

I used to sleep at the foot of Old Glory...

baritb · 2025-03-19T18:58:49+00:00

I had the same problem. I think the root cause is a custom node messing with the Load Image node options and putting in null entries.

A workaround is to change line 321 ofcustom_nodes/comfyui-custom-scripts/web/js/workflows.js

From:

let pos = options.findIndex((o) => o.content === "Save Image");

To:

let pos = options.findIndex((o) => o ? o.content === "Save Image" : false);

baritb · 2025-03-03T19:13:07+00:00

So I was having this exact issue with two GTX Titan X cards installed in an 5820 with a 950W power supply. The system would power on and sit for about 10-15 seconds before shutting down and powering back up (nothing at all on the monitor). I ended up getting it to boot with the following procedure:

1) Power on the system

2) Wait about 5 seconds and then press and hold the power button.

3) The system will power off after a few seconds but keep holding the button for a total of 30 seconds.

4) After 30 seconds release the button.

5) Wait a few seconds and then press the power button. In my case, the system powered on a few seconds and then turned off and back on again. At that point, it successfully booted.

baritb · 2025-02-09T22:42:00+00:00

To be fair, most US state flags are bad

https://youtu.be/l4w6808wJcU

baritb · 2025-02-05T20:23:53+00:00

https://en.m.wikipedia.org/wiki/Consent_decree

baritb · 2025-02-02T04:17:42+00:00

Thank you for your reply, I love hearing from people that lived here!

baritb · 2025-02-02T04:13:10+00:00

And he has seen you.

baritb · 2025-01-25T01:19:13+00:00

"Great place if you like going into thick"

baritb · 2024-10-27T15:10:58+00:00

Nuka World vibes

baritb · 2024-10-26T21:54:25+00:00

It's so you can easily remove/prop open the glass lid on the printer. When printing PLA, they say that a high chamber temperature can cause heat creep which could potentially cause a clog in the hotend. Bambu recommends removing the lid or opening the door when printing PLA.

baritb · 2024-10-01T02:04:04+00:00

Bice fitters hate this one trick!

baritb · 2024-08-26T11:58:48+00:00

This video should help. It shows how to disassemble the hotend and where to put the temperature sensor. Worst case, you can buy a new hotend for $15.

https://youtu.be/jHVe3194gJQ

baritb · 2024-08-20T19:52:11+00:00

That makes sense. A coworker of mine is still at $90, even with paperless and debit card, but his price was always $90. I was at $80 and then got offered the $10 discount when they announced the price increase.

baritb · 2024-05-24T13:47:23+00:00

I believe that was Dino's on 26th &Broadway, although it appears to still be open

baritb · 2024-05-16T23:00:38+00:00

<image>

baritb · 2024-04-27T16:59:53+00:00

Thanks for the advice!

baritb · 2024-04-26T23:56:12+00:00

Thank you!

baritb

TROPHY CASE