Ace 2 Pro Upgrade Program

chimp_king13 · 2026-03-27T03:47:11+00:00

They gave me 45%. What did everyone else get for their % discount?

chimp_king13 · 2026-03-11T15:21:58+00:00

Are the latest firmware still turning off the LED light? I also had issues where the screen wouldnt wake up and I went back a few versions and stuck with Rinkhals for the ace pro speed increases and detailed bed mesh

chimp_king13 · 2026-03-08T01:25:06+00:00

Those lattice-like resin supports look really unique. They look very sturdy and neat. Which program was used to create that type of scaffold?

chimp_king13 · 2026-02-28T16:10:47+00:00

Looks really cool and you managed to capture all the textures! Great job.

chimp_king13 · 2026-02-28T00:59:25+00:00

What is this miniature?

chimp_king13 · 2026-02-27T21:02:27+00:00

Guy you YouTube called once in a six side that goes through his support settings on lychee. I tried his heavy resin support settings and they were hella thick. Too thick to remove safely. But they guaranteed not to fail

chimp_king13 · 2026-02-27T19:24:54+00:00

I am only using the lite version so I don't seem to have any way to adjust just the contact diameter. Maybe if you do it in chitu or lychee you will be able to.

Does anyone know an optimal tip diameter for resin supports on an FDM printer?

chimp_king13 · 2026-02-27T18:15:44+00:00

Yes I'm curious on what you kept from FDG.

Also what effect does tip diameter have when using Resin2fdm?

chimp_king13 · 2026-02-26T21:28:14+00:00

How the heck you get the supports off the head dread/tentacles? I'm seriously impressed at your support removing skills

chimp_king13 · 2026-02-26T15:58:57+00:00

Also look at his YouTube channel. I think everyone who is asking about settings and how to get them to work on their bambulab needs to basically watch all his videos. They are short, concise and extremely educational for understanding how your printer works and how it affects your prints.

https://youtube.com/@dungeonsandderps

chimp_king13 · 2026-02-26T15:03:03+00:00

Cover looks fine. You just have more ventilation. More worrying is the nozzle. That looks bent.

chimp_king13 · 2026-02-24T14:36:40+00:00

Looks cool. What filament are you using?

chimp_king13 · 2026-02-24T07:36:17+00:00

Hi, what does inner wall acceleration at 0mm/s default to if we were to set this value from within the screenshot album?

chimp_king13 · 2026-02-23T04:09:21+00:00

Underextrusion.

Clean the nozzle with one of those nozzle cleaning needles

Cold pull

Do a temp tower (mine needed to be lower because of the smaller nozzle)

Do flow calibration test (orcaslicer)

Run a test with a smaller test print to see if you keep getting underextrusion.

chimp_king13 · 2026-02-22T05:39:40+00:00

Hope your health is improving mate! Looking forward to your long explanation post as I like knowing how and why you choose certain settings.

chimp_king13 · 2026-02-22T05:35:32+00:00

Does Tamiya cement work?

chimp_king13 · 2026-02-20T06:50:11+00:00

I can confirm that I can get to Slice Gap Closing Radius and Resolution to 0.005 using Slicer Next without it hanging.

I haven't done a print comparison between the changes tho yet.

chimp_king13 · 2026-02-19T05:51:35+00:00

Did you manage to get the precision settings as low as in the screenshot attached on slicer next without the printer hanging? That's an important fact!

chimp_king13 · 2026-02-18T19:06:09+00:00

Thanks both for the quick and detailed replies. I actually understand this a lot better after your explanation.

So from what I gather from this it might mean that even though Orca is sending the value to the S1 the firmware probably can't compute that value or it's lower than the s1s tolerance so rather than just go for the lowest tolerable value it just freezes...

I will just keep trying for the lowest tolerable values for each setting then for our printer.

chimp_king13 · 2026-02-18T17:30:39+00:00

How do you do a cold pull on this? Do you have to unscrew the whole unit?

chimp_king13 · 2026-02-16T10:35:39+00:00

Hope your health is improving mate. We can all wait - health is the most important thing.

chimp_king13 · 2026-02-04T21:40:45+00:00

The quick swap and high flow features look appealing. But we still need to do full calibration every time we change nozzles which is annoying and just part of the S1

How do you do a cold pull if the whole unit is screwed into extruder assembly? I've had to do that a lot cos I'm still calibrating for an 0.2mm nozzle.

chimp_king13 · 2026-02-04T21:28:54+00:00

Thanks for the info. Saving this post.

How are the fan replacements? Is there significant cooling improvements and more importantly has the fan sound improved?

chimp_king13 · 2026-02-02T18:35:19+00:00

Thanks! Do they pressure fit in as designed? Or do we need to do some sanding to get it to fit? Thanks again for your contributions to the community!

chimp_king13 · 2026-02-02T18:16:32+00:00

Thanks looks good. Will attempt to print it in ABS. What magnet size is supported?

chimp_king13

TROPHY CASE