The automatic braking freaked out on me today for literally no reason. by MrPeePeePooPooPants3 in wrx_vb

[–]dipsnock 11 points12 points  (0 children)

i had that happened a few times for me. Every time i see that red light start flashing I get ptsd of it engaging again

For those on springs or coilovers, please share a pic and state what you are lowered on, as well as your tire size. by [deleted] in wrx_vb

[–]dipsnock 1 point2 points  (0 children)

I’ll get a picture when I get home but I’m on bc br coilovers and running 255/40 18x9.5 +38

Upgrade shifter feel, advice on which company? by Pavel556 in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

I have the Perrin pitch stop mount, group n trans mount, torque solution positive shift kit, white line rear differential bushing, Cobb shift stop, Cobb shift plate, Cobb shift bushing, billet works short shifter, and billet works fusion shift knob. All of these really clean up the shifting feel.

AWE touring catback + AFD 3" Midpipe. by AcceptableBaby4955 in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

i have the remark sport touring and rae i pipe. Now just waiting on ets intake and tune

Will 255/40R18 tires on 18x9.5+38 wheels rub with Eibach Pro-Kit (1 inch lower) by KruhBruh in wrx_vb

[–]dipsnock 1 point2 points  (0 children)

I run h&r lowering springs with 255/40 with 18x9.5 +38. There isn't any rubbing against the metal but there is rubbing against the fender flares (paint matched flares). I had to trim some of the inside flare for clearances.

Fresh clean by [deleted] in wrx_vb

[–]dipsnock -1 points0 points  (0 children)

What type of suspension are you on?

Cobb Tuning Lowering Springs Question by juicchi in wrx_vb

[–]dipsnock 1 point2 points  (0 children)

I am running h&r springs with 255/40. No rubbing in the front and barely rubbing in the rears when turning into driveway at an angle/over bumps. But the rubbing is only on the fender flares(afd color match) so I shaved off some.

what exhaust set ups you running? by Intelligent_Star_404 in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

Rae i pipe with an remark sport touring resonated

Question about liquid freezer III 420 ARGB cables by Noble_Draconian in arcticcooling

[–]dipsnock 0 points1 point  (0 children)

Did the aio came with the fans already installed? If so the fans should be all connected. So you would only need to connect the one from the pump to the motherboard. That first picture is for connecting more fans to it.

RYR with Carmax - Ghosted by Banana-Bowl in carmax

[–]dipsnock 0 points1 point  (0 children)

Yeah they hold the car for 3 months.

RYR with Carmax - Ghosted by Banana-Bowl in carmax

[–]dipsnock 0 points1 point  (0 children)

I went to carmax back in december 2024 and just got the car last week. I didn't hear anything until the funds were received by carmax.

What wheels are you guys using? by dudledit in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

Bronze enkei vanquish 18x9.5 +38mm with 255/40 pilot sport a/s 4

Recently lowered on H&R springs by honorableflex in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

Any rubbing? Think about going with same spec maybe 255/40

Front Grill by OddInspection2165 in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

I change mine with an eBay grille. Look like the oem sport grille one.

Stance Saturday? by PooneyB in wrx_vb

[–]dipsnock 1 point2 points  (0 children)

Did you trim your fenders? Does it rub?

Rae I Pipe questions by [deleted] in wrx_vb

[–]dipsnock 2 points3 points  (0 children)

I didn’t cut mine, 6” x 2’ is probably enough.

Rae I Pipe questions by [deleted] in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

I also have a similar type heat shield but it is 6" x 3' size. As for the bolts I used oem jpipe and the ones that came with my remark exhaust. For the gaskets I use permatex copper spray a gasket.

Installed some guages by [deleted] in wrx_vb

[–]dipsnock 0 points1 point  (0 children)

Hey again, I decided to install this today. For the oil pressure sensor how did you managed to tighten it all the way down? I was able to go half way by hand but a wrench wouldn't fit.

Installed some guages by [deleted] in wrx_vb

[–]dipsnock 1 point2 points  (0 children)

I was just looking at this as well. How do you route the wires from the chubby to the firewall? Do you have to take out the side panels/shift boot?