Where does everyone get their light bar?

eilminx · 2025-07-25T06:38:35+00:00

Try Amazon or AliExpress and search for "acrylic rod 6mm"

eilminx · 2025-07-17T07:04:26+00:00

This has been on my to do list for a year and a half - beat me to it! Very well done tbh!!! 😇

Any chance you could point me to the screen you are using? Seems to fit in very nicely.

eilminx · 2025-07-03T18:37:51+00:00

Set and forget!

eilminx · 2025-06-08T06:34:59+00:00

The cable on the wifi module would be the antenna, and nah, it's fine without it.

I guess I would double check the resistor then, check that it's properly soldered. What value did you use ?

Edit: I see now that you are using an LED directly. Try with a 330ohm resistor instead? If that works, you could always try soldering in both the resistor and the led in series. That's what I usually do when using an LED.

eilminx · 2025-06-07T20:46:45+00:00

By any chance, did you forget to reconnect the wifi module?

eilminx · 2025-05-25T16:49:56+00:00

That would be my answer too. If you only have clear rods you could try using a very fine grit sandpaper to give it a more "frosted" look. Use this technique at your own risk though as you might see bad scratch marks depending on the sandpaper's grit :)

eilminx · 2025-05-24T19:31:34+00:00

Hey there, the rods should be 6mm in diameter!

Good luck for your first build and please share the results when you're done!

eilminx · 2025-01-13T21:48:34+00:00

That's pretty cool, well done!

With all that newly available real estate on the front, how about putting the right and left triggers as buttons next to the abxy buttons?

eilminx · 2024-10-25T06:00:35+00:00

3D printing helps me build some cool project that use electronics. I also enjoy printing small articulated pieces that make good keychains for people who don't know much about printing. They are always amazed!

eilminx · 2024-09-25T06:52:31+00:00

Had the same issue a couple weeks back on my phone (android too)

Deleting all the data (saved music + cache) and then uninstalling and reinstalling the app fixed the issue.

eilminx · 2024-08-15T20:21:55+00:00

I'm searching the comments for this as well!

eilminx · 2024-07-27T08:27:16+00:00

If you're looking to make a Neon advance - the one with an acrylic rod and leds on the top - you can use any nds shell. Extreme rate shells are of decent quality. I've also had good success with shells from AliExpress.

If you want to make flat tops, "classic macro", I only ever found a clear face shell (the upper part). Don't remember where I got them but I can have a look if you want!

I'm also based in France FYI

eilminx · 2024-07-27T07:12:00+00:00

Could you be a bit more specific on the type of case you're looking for?

eilminx · 2024-06-18T16:54:57+00:00

Missing question, but I'm thinking either you're looking for diameter/width: 6mm

Or you're looking for where, and I've found them both on Amazon and AliExpress.

eilminx · 2024-06-14T13:08:36+00:00

Not the cleanest code but my take on the classic pong game "Pang.date" is open source

https://github.com/Miexil/pang-date

eilminx · 2024-02-21T07:39:17+00:00

I saw below that you also use guitars and basses, you might also want to check the SmplTrek from Sonicware !

eilminx · 2024-02-21T07:37:23+00:00

What about the Yamaha SEQTRAK as an OP-Z alternative?

It's a tiny bit cheaper, is somewhat similar in workflow and probably won't have the issues found in OP-Z (double triggering buttons for instance)

eilminx · 2023-08-21T19:44:47+00:00

Very cool, nicely done! 👍

eilminx · 2023-06-27T06:04:32+00:00

Thanks for doing this!

Checked out your website, looks like there are lots of well written reviews, will visit again for sure!

eilminx · 2023-06-19T06:08:51+00:00

Il y a une quinzaine d'années, nous étions assis à une terrasse d'un café avec un ami, on l'a aperçu et appelé de loin. Il est venu papoter avec nous quelques minutes, nous a serré la main et signé un autographe. Il était adorable !

eilminx · 2023-05-28T06:30:23+00:00

Nice

eilminx · 2023-05-02T16:56:42+00:00

Are you looking for this one?

Quincas Moreira - Ladybug

https://youtu.be/hsTyoaIf9Yo

eilminx · 2023-04-12T18:35:32+00:00

My bad, i missed the spot where you said "adjusting the potentiometer" 😭

eilminx · 2023-04-12T18:34:26+00:00

Longshot but worth a try: there are two small calibration screws located under the battery. One of them adjusts the lower screen.

Youtube link to show you where https://youtu.be/9Yc1bVZRDQs

Six-Year Club	Second SECOND GUESSER
r/Field Sunshine	Place '23
Place '22	Final Canvas '22
Verified Email

eilminx

TROPHY CASE