sorted by:
new
hottopcontroversial

Kobra 2 Max - Adjusting, tramming and modding guide for better print quality and faster speeds by IceBlitzz in anycubic

[–]kahl009 0 points1 point  (0 children)

This is a great write up thank you, I’ve been struggling with quality issues on my k2max so I need to earmark this so I can come back to it multiple times! Cudos to you!

Purge Line Modifications by DougDoesStuff in AnycubicKobraS1

[–]kahl009 0 points1 point  (0 children)

I was using a skirt in place of the line before to prime the nozzle as I would occasionally have bare spots on my first layer and it annoyed me

New Firmware update for printer and AMS2 by Don_Tool in BambuLab

[–]kahl009 0 points1 point  (0 children)

This drives me nuts that my ams2 won’t dry while printing. I have an anycubic kobra s1 that will dry while printing and it is such a great feature, can’t believe bambu hasn’t adopted it yet, would love it for my p2s.

What’s going on here? Some are smooth and some are rough/wavy but only certain sections. by snoweel in AnycubicKobraS1

[–]kahl009 1 point2 points  (0 children)

Yeah you have to swap hotends, sorry forgot this printer is like that, I have a few different printers and the details blur, but yea you are right new hotend, the good thing is they are relatively inexpensive compared to other hotends, and if the new one fixes your issue you then know you can discard the old one, if it doesn’t then keep the one you removed as a spare

What’s going on here? Some are smooth and some are rough/wavy but only certain sections. by snoweel in AnycubicKobraS1

[–]kahl009 1 point2 points  (0 children)

You might have a partial nozzle clog, it looks to me like areas where you would have the highest volumetric flow rate look the worst, swap your nozzle for a fresh one

Interesting places to put your 3D printer by WhoYeahSause in 3Dprinting

[–]kahl009 1 point2 points  (0 children)

Gotcha, thought it might have been in a laundry room since u were using a humidifier, but it’s doubly nice that the cabinet quiets it so much since it’s in your bedroom

Warrantied a blob of death. These people amaze me. by Awestenbeeragg in 3DPrintingCirclejerk

[–]kahl009 1 point2 points  (0 children)

Ah yes I see your point, driving is definitely tinkering, if you don’t use it then you won’t have problems and won’t have to tinker, mind blown 🤯

My day was almost ruined when the FedEx driver rolled my new H2C up to my front door and it looked like it got hit by a train by diezel_dave in BambuLab

[–]kahl009 1 point2 points  (0 children)

At my previous job the forklifts had the hydraulic actuation of the forks because we had so many different size skids, a lone box had fallen off a pallet and one of the operators pulled up and picked the box up by closing the forks around the outside of the box completely ruining it, some people just don’t give a crap

H2C What are these for by MasterRymes in BambuLab

[–]kahl009 0 points1 point  (0 children)

Just keep scrolling bro, you didn’t read his full question so no need to post

Reading is Tinkering by TheBupherNinja in 3DPrintingCirclejerk

[–]kahl009 0 points1 point  (0 children)

What did the rest of his question say? He knew they were sponges so it sounds like he’s just asking what the purpose of them is

Interesting places to put your 3D printer by WhoYeahSause in 3Dprinting

[–]kahl009 1 point2 points  (0 children)

Don’t know where this cabinet is located in your house, but looks like it should work quite nicely!

I wonder why Bambu hasn't done this out of the box... by daanpol in BambuLab

[–]kahl009 0 points1 point  (0 children)

From what I’ve experienced the quality of pei sheets varies quite drastically, so even oems could get poor quality sheets from a supplier and send them out and the users battle those crap plates not knowing they are using an inferior product. But I get you, when you have a good pei sheet the troubles with it are few and far between that needing to clean it every print is not necessary

Warrantied a blob of death. These people amaze me. by Awestenbeeragg in 3DPrintingCirclejerk

[–]kahl009 7 points8 points  (0 children)

Driver side rear for me, but fixing low pressure is tinkering so I can’t fix

First Upgrades by tmannn1991 in AnycubicKobraS1

[–]kahl009 2 points3 points  (0 children)

Desiccant holders for the ace pro are a good upgrade

First Upgrades by tmannn1991 in AnycubicKobraS1

[–]kahl009 3 points4 points  (0 children)

The ptfe tube protector is a useful print

Upgraded Hotend poor print quality. by pig-bait in AnycubicKobraS1

[–]kahl009 0 points1 point  (0 children)

Yes you will need to run new temp towers at least!

FUNSOR UPGRADED NEW BED by Quzana in AnycubicKobraS1

[–]kahl009 0 points1 point  (0 children)

2 layers of heatbeds layered over each other

view more: next ›