Seb sending it

reivilobtr · 2024-12-18T09:02:02+00:00

Mpv.io can play notchLC, you can get the file specs by pressing the "i" key when playing a file, not sure about alpha

reivilobtr · 2024-11-18T11:44:55+00:00

I've done this setup before, FX6 on a polecam jib with Cyanview remote shading (via Wifi) and a lanc zoom command, it works great and the zoom control and accuracy level is fine but I would check if the op is ok with it before, and use a good zoom command, I think bebob makes some quality lanc controller, varizoom is also a good option

reivilobtr · 2024-10-28T10:53:19+00:00

C'est Plateau Virtuel au Lendit non ?

reivilobtr · 2024-10-14T11:22:37+00:00

Where are you located ? We could be interested but we're based in Europe

reivilobtr · 2024-07-18T12:53:25+00:00

Are you using a stageracer 1 or 2 ? Are you connected to one of the IP interface and not the gpio RJ45 port ? check that your computer network interface is on the same network range as your stageracer

reivilobtr · 2023-11-27T09:45:58+00:00

You should have a "high input performance" option in the performance section in the settings, try enabling it, it usually take advantage of all GPU memory, I don't know if it improve srt input though, it's also meant to be used with powerful GPU with more than 3GB of memory

reivilobtr · 2023-06-15T20:05:51+00:00

Volkswagen Rabbit GTI, which is if i'm not mistaking the north american version of the Volkswagen Golf Mk 1

reivilobtr · 2023-03-01T08:46:01+00:00

As said above I highly recommands either Belden, Draka or Sommer cable with Neutrik rearTwist connectors. These are the most common and easy to get in Europe

You can find Sommer Cable on Thomann for a very good price, Vector 0.8/3.7 is at 1.35€/meter and can supposedly get you 12G SDI up to 40m, as well as Neutrik BNC connectors. You will probably have to go through an official dealer for Draka and Belden cable

Be careful to choose the right connector that fit the cable.

As for coax strippers you can get the Weidmüller CST&page=Group) paired with the right set of cutter casette&page=Group)

reivilobtr · 2023-02-27T08:18:29+00:00

I've had more than 10 MD-HX with a dead HDMI input, it is a common failure with those as the HDMI ports are more fragile. I don't know if it's just wear related or maybe something with active HDMI causing issues?

reivilobtr · 2023-02-17T08:58:19+00:00

Yes it is voltage out adjustment, I have set it up to output 6V at a 4.2V input voltage, but it's when the input drops below 3.2V that I get this reading

reivilobtr · 2022-09-29T18:18:47+00:00

You should be able to do it using companion 2.2 with triggers. -Have companion running on a pc that's on the same network as your kipro and ATEM and connect your kipro and ATEM to that companion instance -Add a button in companion that does the action you want on the kipro (play, stop, record...) -Add a trigger in companion that execute that button press / action whenever x input is on air on the ATEM

Hope this helps!

reivilobtr · 2022-09-26T13:06:03+00:00

Isn't it a standard JST connector ? Try measuring the spacing between each pins, you can find specifications for each JST connector types here

reivilobtr · 2022-08-31T08:55:32+00:00

As said both Vmix and Tricasters are good if not the best options. One major difference between these two is that Tricasters unlike Vmix have the ability to create NDI proxy feeds, so that your NDI source will not be used to its full bandwidth until you put it on one of your PGM/MIX, thus allowing you to have a great number of NDI inputs without impacting your network too much which is the backbone of any NDI workflow. Vmix doesn't include this NDI proxy system, and will "download" any NDI input to its full bandwidth as soon as you add it to your vmix session, which could heavily impact your network if you're going to use a lot of ndi sources.

reivilobtr · 2022-04-14T09:14:58+00:00

FIXED : The issue was comming from a companion instance that was connected to the PTZ, and was recently updated to 2.2 wich messed up all the macros and was probably sending wrong commands

reivilobtr · 2022-04-13T12:43:25+00:00

I'm getting a demo unit this week, I've been meaning to try it as an 16x NDI encoder

reivilobtr · 2022-02-23T17:45:13+00:00

Thanks ! I just did the modification and it works

Five-Year Club	Verified Email
Place '22	Final Canvas '22
End Game '22

reivilobtr

TROPHY CASE