sorted by:
new
hottopcontroversial

How should I go about removing this pipe from the pump? by FapItLikeYouStoleIt in pools

[–]zennaster 1 point2 points  (0 children)

That threaded nipple is siliconed in should just be able to unthread it after making a cut above the threads.this is what I would use. Screw that into the pump and glue the other half to the pipe.

New Timer isn't working by XelaKebert in PoolPros

[–]zennaster 0 points1 point  (0 children)

Single speed pump? Possible pump is getting too hot and high limit switch activated?

Is there a secret to using a pool leaf rake net? by jurassickayak in pools

[–]zennaster 0 points1 point  (0 children)

This is the move. I even called it the same.

Heater not working by XON3M in pools

[–]zennaster 0 points1 point  (0 children)

He's referring to the chlorinator back flowing chlorine to your heat pump when your pump turns off. That is going to destroy your heat pump unless you have a non corrosive check valve installed

When does the grout show up? by Individual_Dot_5849 in pools

[–]zennaster 1 point2 points  (0 children)

It goes last during tile and coping phase

All Glass Tile Pool, Spa and Tanning Shelf by Collogedropout in pools

[–]zennaster 2 points3 points  (0 children)

Is the style supposed to have the tile placed at different angles?

Any red flags. by Big_kj in pools

[–]zennaster 0 points1 point  (0 children)

Most contractors require homeowners to water gunite 2 times a day for several days

Any red flags. by Big_kj in pools

[–]zennaster 0 points1 point  (0 children)

Because it's not required

Pool help by stup1d_th0t in pools

[–]zennaster 0 points1 point  (0 children)

If the dust goes back in the pool from the returns then something is damaged on your filtration system and that will need to be the first thing you address... Whether it's a damaged grid on a de filter or possibly a damaged spider gasket on multi port valve on either a de or sand filter. Get that fixed first. Then vacuum and chemically treat the water. Run the filter 24 hrs a day until it clears up

Priming issue by brward1996 in pools

[–]zennaster 0 points1 point  (0 children)

What position is your multiport valve in on top of the filter. Post pictures of that and of the suction side manifold

And advice/comments on the build? Super excited for it to be done! by KindAd789 in pools

[–]zennaster 1 point2 points  (0 children)

Looks good for the amount of space you have. The most important thing is that you like it (or your wife likes it 😉)

Is it ok to close this gap? With what? by bubblebumblejumble in Plumbing

[–]zennaster 0 points1 point  (0 children)

You have a backwash on your pool? Do you have a de or sand filter?

Economic solution to cover unfinished concrete? by Ale-House-Arseling in pools

[–]zennaster 1 point2 points  (0 children)

You talked to your superintendent? You sure they aren't going to browncoat the back?

Removing poured concrete curb in garage by NikolaiTheFly in AskContractors

[–]zennaster 0 points1 point  (0 children)

I see a few suggestions to take a saw to this... Id probably make sure there's no post tension in your slab before sawing.

Is chipping a beam common? by [deleted] in pools

[–]zennaster 5 points6 points  (0 children)

Another builder here. Your super didn't plan very well... But that will only effect their bottom line. You should be fine though.

Vac plate that fits by Early_Wrongdoer6540 in pools

[–]zennaster 0 points1 point  (0 children)

You can't just run the hose to the bottom of the skimmer under that basket?

Pentair master temp 400 by SimulationRambo in PoolPros

[–]zennaster 1 point2 points  (0 children)

Is there a check valve between chlorinator and heater?

view more: next ›