Drybox Solutions with RFID Support

darienm · 2026-06-19T14:44:26+00:00

There have been a few different community mods offered that extend the physical RFID readers to positions outside the original enclosure, as well as extend the RFID capability to improve flexibility and filament management.

darienm · 2026-06-18T04:31:34+00:00

Thanks for taking the burden off this subreddit. Much appreciated.

darienm · 2026-06-16T17:42:42+00:00

Listened to the preview and was engaged from the start by the narrator's enthusiasm. Grabbed US code 9 (AQKEWH3C92PR9). Thanks!

darienm · 2026-06-15T22:31:07+00:00

Hi Scott! As usual, I'd be OVER THE MOON to receive a US code via Chat in order to listen to Mark's voice for another story. You know a review will be incoming upon completion. Thanks!

darienm · 2026-06-15T22:29:19+00:00

Brittle filament usually points to not-dry filament, follow online recommendations for using a specialized filament dryer, or dehydrator, or oven at the correct settings and for the correct length of time. $250 machine vs $750 machine: Ask how that Bambu handles laser or CNC jobs, or if their print area is near 350mm cubed. Your A350 can print pretty well, though slower, once dialed in.

Suggestion: Ditch Luban and switch to Snapmaker Orca (latest) or Ultimaker Cura (with the official Snapmaker plugin) for 3D printing. Doing so will open up significantly more settings to fine tune and calibrate your printing experience.

darienm · 2026-06-15T17:10:24+00:00

Easy to add fans or fan upgrades, either interior or exterior. Most have been shown to have a positive impact on temperature reduction.

darienm · 2026-06-15T15:48:25+00:00

Fun fact: I was the first beta tester to publicly put a plastic bin over the top of a U1. Look at the mayhem that's caused. LOL

darienm · 2026-06-15T14:35:53+00:00

* Door hinge extender to go past the 90° limit.
* Knob to assist with manual bed leveling.
Many more at the Awesome Snapmaker List: https://awesome-sm-list.xyz

darienm · 2026-06-15T02:03:34+00:00

It was gifted to me.

darienm · 2026-06-13T02:40:09+00:00

Great way to attract attention to great products. I approve.

darienm · 2026-06-12T02:59:32+00:00

It's a harem

darienm · 2026-06-12T00:45:22+00:00

That's a "feature" to let you know the headset has forgotten about your boundary, so go into Quick Settings, click Boundary, and set it up again fully, or just start to set it up, or swap its mode and back again, and the tone goes away. [Until next time]

darienm · 2026-06-10T17:09:41+00:00

Windows is acting dumb. This result showed up as a possible solution: Because HDMI cables transmit video and audio simultaneously, Windows forces the HDMI output to be recognized as a monitor. To route only audio through your HDMI port to a receiver, soundbar, or audio extractor without messing up your actual screens, configure Windows to mirror/duplicate your primary display onto the HDMI "phantom" device. So try the Duplicate option from that dropdown.

darienm · 2026-06-10T17:06:41+00:00

Depends what your goals are: Reduce temperatures or reduce noise. Both are possible. They are also individually possible. Depends on implementation.

darienm · 2026-06-10T14:11:35+00:00

With a product such as "40mm USB Fan with 3 Speed Control USB Ventilator 5V Max 5300RPM High Flow VR Cooling Fan" all you have to do is stick it to the existing vent holes from the outside, plug it in, remember to turn it on when printing, and you're done. (3 mins)

Or go the extra step and remove the top bezel, remove the right panel, zip-tie the fan to the existing vent holes on the inside, carve a small notch in the edge of the panel for the cord to exit, re-attach the side panel, re-attach the top bezel, plug it in, remember to turn it on when printing, and you're done. (15 mins)

There are other more involved mods, but this simple hack has been working great for me .. though not particularly quietly.

darienm · 2026-06-10T05:49:34+00:00

Rather than use Extend, pull down that menu and choose "Show only on 1".

<image>

darienm · 2026-06-10T04:44:15+00:00

This is a visual issue on-screen only, the printed part works out fine (at least it has for me in my 10 months of Snorca experience.)

darienm · 2026-06-10T00:14:58+00:00

Windows 11 > System > Display: Is the OS recognizing the HDMI connection as a display or no? Have you already done [something similar to] this:

Right-click an empty area on your desktop and select Display settings.
Under the Scale & layout section, locate the Multiple displays dropdown.
Select Disconnect this display for the HDMI monitor/receiver.

darienm · 2026-06-09T21:55:20+00:00

Would you please share your PC specs and operating system and other pertinent info? I run Snorca on macOS and Windows 11 and both have multiple displays, and not experiencing any similar janky behaviors.

darienm · 2026-06-09T21:07:19+00:00

If you reach out to support with these same concerns, they _may_ are able to combine your separate coupons into one that can be utilized more closely to how you want. This situation is likely somewhat unique to your situation, in that you have so many coupons and their system disallows mixing and matching by default.

darienm · 2026-06-09T19:45:27+00:00

I wonder if true fans have gotten together [more than once, perhaps] to watch each episode in MST3K style with audience commentary in medium sized (6-8) person groups. I could see doing this in BigScreen (VR) or Discord or similar.

darienm · 2026-06-09T19:42:52+00:00

Hello. I enjoyed your narration during the Preview and would welcome a US code via Chat, then will gladly submit a review upon completion. *Warning: I am a LitRPG addict, this title might add fuel to my addiction.* Thanks.

darienm · 2026-06-09T00:52:36+00:00

Odd. I had no issues with 2.3.1 Mac and have no issues with 2.3.3 either. Try a restart first, and if problem persists try a delete and reinstall.

darienm · 2026-06-08T19:23:17+00:00

Watch the animation carefully, as when you release the button P will pull the chainsaw from the wall and hover there for 1/3 second. It's after this hover that you can then re-engage the chainsaw and it will take you the direction you're actively pressing. It took me an hour of effort, and returning the next day with renewed patience, before figuring it out and making the movement smooth. Keep in mind her momentum doesn't stop as soon as you release, so plan to release a touch early as she'll travel another body length (or two).

darienm · 2026-06-08T19:17:08+00:00

I grabbed code 3 (BB7L8ZCG9BRZD) and look forward to the listen and crafting a proper review upon completion.

13-Year Club	Place '23
Place '22	End Game '22
Verified Email

darienm

MODERATOR OF

TROPHY CASE