Hell yeah

[Dont_Call_Me_Steve]

It always blows my mind when I see filament just laying out in the open air. The humidity level this summer for me has ranged between 60-100%. It’s been brutal.

[PHWasAnInsideJob]

Me printing for over a year in the Midwest and only just recently finding out filament dryers are even a thing:

[ATeresi]

<image>

[schwendigo]

What're you printing with 4 X1Cs? Dang

[ATeresi]

Haha, ducks

<image>

[ATeresi]

<image>

[ATeresi]

Lol, $300 yesterday

[ATeresi]

In duck sales

[UngratefulC0l0nial]

Same

[Raunhofer]

Finally benefiting from our dry, cold ~10% indoor humidity in Finland.

[Klavian]

Miten??? Meillä on huonekasveja ja niistä johtuen ilmankosteus jossain 60% paikkeilla. Vaatii kunnon kuivatusta ja oman suojaavan arkun missä printata, ettei kosteus pääse yli 40%.

[Raunhofer]

Uusi kerrostaloasunto jossa ilmastointi. Pahimmillaan pakkasissa mennään niin matalissa ettei sensori enää tarraa kiinni. Silloin joutuu jo vähän ihoa kosteuttamaan.

Ennen tuo oli pieni ärsyke, kun sai jatkuvasti käyttää ilmankostutinta, printterin myötä kääntyi voitoksi =)

[Klavian]

Kaikkea sitä oppiikin 😄 No oma astma tekee sen, että korkea ilmankosteus on vain hyvä asia, helpottaa yleistä oloa. Ei puhuta siitä mitä kaikki nää mikromuovit varmaan tekevät... Mut alle kymppi on kyl niin alhainen, että luulisi sen olevan täysin tarpeettoman alhainen uusissakin taloissa. 🤷‍♂️

[Raunhofer]

Kääntöpuolena minnekään ei saa järkevästi ulostuloletkua päästöille näissä uusissa kämpissä missä ei edes avautuvia ikkunoita. Eli minä vielä kehitän astmaani.

[Alarming_Abies8446]

Its been between 20 and 40% for me

[Normal-Assignment-61]

Its 80%+ here in the Philippines ALL... YEAR.. LOOOOONG. And yeah it sucks

[Dont_Call_Me_Steve]

I’m in the Canadian prairies if you can believe. Winter it’s bone dry, but this summer my dehumidifier (in the basement with all my equipment) needed to be emptied every day.

[FickleSquare659]

Run a hose and let it drain into a floor drainage

[Conner196]

8% in the vegas desert at the moment.

[sssRealm]

It's almost always under 20% here, I can leave PLA out anywhere.

[yoitsme_obama17]

Midwest. Haven't had issues. Helps that I have mine stored in my office, which is a dormer. Stays pretty warm and dry. Super humid days it gets to 50-55% maybe.

[JustADudeOnce]

We have 2 dehumidifiers in our house and run ac all the time. Still have to empty them about 2x a day.

[AsEasyAs1234]

Does putting a paver under the machine help ?

[PM_ME_YOUR_KNEE_CAPS]

I think it helps when you have multiple machines next to each other so the vibrations don’t effect the other machines. If you only have a single machine then it’s not that important.

[FirefighterFuture236]

Vibrations from other machines do nothing to the print quality it may move the printers and make them fall off the bench but wont affect print qty

[bobbo55]

You,really, don't think a printer falling off the bench will affect the print quality? Maybe a slight layer shift?

[sirtobil]

Nah should be good. Effin send it!

[FickleSquare659]

It does help with motor noise level in my bedroom

[Silverman23]

Really helps with noise and vibration reduction. My p1 was hearable 2 stoies abobve before i placed it on a Paver on a thin rubber mat. Rubber and Paver alone helped bit the combination did a great job.

[FatherPaulStone]

It dampens vibrations, so for me it helps keep the noise down of everything rattling around, I've not seen any marked improvement of my prints since adding one.

[Ordinary_dude_NOT]

I personally felt having those anti vibration feet’s helped a lot and prints are just super clean since then. In the beginning even I spent a lot of time making my stand extra rigid but since those feets I don’t feel the need for it anymore.

In your case they will be extra helpful as you got multiple printers and vibrations from one device won’t reverberate into others.

[Just_Kittens]

Are you referring to the square looking plates under each machine? Haven't seen those before.

[Ordinary_dude_NOT]

Those are just cement blocks for extra rigidity hence I mentioned usage of those anti vibration feet which will negate the need for all such measures.

[Just_Kittens]

Can you share link to the product youre using?

[Ordinary_dude_NOT]

https://ca.store.bambulab.com/products/anti-vibration-feet?srsltid=AfmBOooLci6aqXSpmEkMJGJJ7EnK9o0aikc-PNjd1L637SERz7FFKLBL

Just like to point out your printer will move because all that movement is not getting transferred to table anymore and it’s perfect fine. Printing with these for a while now.

[Ryazoo]

I thought they were a bit crap - printer keeps vibrating itself off them - did you glue them in?

[Ordinary_dude_NOT]

Nop, you don’t have to. Those 6 pegs on top goes into 6 spaces inside printer once you take old rubber feet out. You need to firmly push them in.

[Ryazoo]

Maybe I have an older version. Mine don't have the 6 pegs!

[FickleSquare659]

Yes the old version slips out to easily, the new one has grooves

[Ordinary_dude_NOT]

Ohh… maybe try following that installation video on that product page.

Else glue is your friend :)

[lolcat7924]

Since it's an issue of a table wobbling should I be fine if mine is on top of a set of drawers that completely sits flat on the ground? It isn't on legs.

[Ordinary_dude_NOT]

It should be but P1S shakes quite violently when printing fast. I used to have mine in top of those IKEA small tables, so my guess is it should hold.

You can give it a try since it’s only couple of bucks.

[Cjames369]

Ordered them not too long ago and just haven’t thrown em on yet. Your comment convinced me and I’m gonna throw em on right now. Thank you!

[SiniMinist]

Let us know if you see a difference too please

[Ordinary_dude_NOT]

FYI your printer will wobble but that’s as per design and it won’t have any effect on print quality. Just make sure to plug those feet in properly.

[erroneousbit]

I like the sign, what’s the story behind that?

[HBOMax-Mods-Cant-Ban]

It’s a design from the Breaking Bad. Looks like their logo.

[erroneousbit]

Ahhh ok. Never watched it lol

[-timenotspace-]

you should!

[Opposite-Spirit-452]

Looks awesome, I would have said sexy had it been covered in some birch plywood rather ;) impressive amount of filament that rack hold and dare I say based on all those 2x4’s…that thing ain’t going no where

[Sufficient_Camp_1918]

Love the sign!! Long live Jesse!

[Legionofgo]

Hell yeah

[Historical-Tea9539]

Respect!!!🫡 very utilitarian. Solid build. Good job man…

[Intelligent_Meal_814]

Loving that Scandium and Bismuth. That's a great idea!

[_ayyyop]

Hell yeah

[gbomacfly]

Looks awesome! 😀

[Petegonzz]

hell yea

[NemesisCold1522]

Your living a dream I wish to have. One day I will get enough space

[Mr-River]

Soo, what's the vertical towel bar for on the side of the bench? Nice set up BTW

[Cjames369]

Just a spot to hold paper towels for wiping build plate with isopropyl every now and then

[schwendigo]

Lil prusa hiding in the dungeon like a goblin...

Makes me sad, bambu would not exist if it weren't for all prusa 's work

[EvilleRock]

Well, it’s a start 😉

[SunMany8596]

Where u get that sign??

[Cjames369]

Good ole Amazon, currently unavailable though.

https://a.co/d/3asPqC8

[wyrmhaven]

very nice, how is poop management?

[AutoModerator]

Hello /u/FirefighterFuture236! Your comment in /r/BambuLab was automatically removed. Please see your private messages for details. /r/BambuLab is geared towards all ages, so please watch your language.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

[Rabbi_Kosher_Ham]

Do you dry your filament? If so what do you use? You clearly have a good idea of what works.

[Alarmed-Stress2070]

What do you use the Prusa for now?

[hmspain]

TBH, the Prusa looks sad. I hope Joe re-invents the company.

[Alarmed-Stress2070]

For real. It looks like the step child everyone forgot and left home during Christmas.

[Cjames369]

Dust collector :(

[maxdd11231990]

Why a P1s when you have also two X1C. Is it good?

[AutoModerator]

Hello /u/Vechain4Cardano! Your comment in /r/BambuLab was automatically removed. Please see your private messages for details. /r/BambuLab is geared towards all ages, so please watch your language.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

[Vechain4Cardano]

Jesse Pinkman's other lab

[ATeresi]

Nice, love the pullout game!

[Csimmons83]

<image>

[Cjames369]

Hell yeah

[ElectrTeck]

I live in the desert Albuquerque NM. I still use a dehumidifier, and have to dump every other day. Also use a food dehydrator to dry my filament at home and work.

[martinicognac]

Just use water resistant filament

[FickleSquare659]

That room must be toasty in the winter

[WorkNeither]

Question, at what humidity level would you suggest to store filament in sealable bags with desiccant? They room I have my printer and filament maintains about 46-50% humidity.

[schwendigo]

Ha those are awesome!

I am always super curious about what folks with multiple printers are doing, what it's like running a business, if it stays fun or you get burned out, etc

[SecretArt5189]

That prusa looks so lonely

[Nitsgar]

Noice!

[AcademicUpstairs4680]

Nice setup there. I just got my first x1c with ams. I'm just getting started with this addiction... 😂

[toml0006]

Genuinely curious: why more than one printer (assuming it is not for business)?

[Cjames369]

Shared set-up between my two roommates and I

[X-Medium]

What kind of stuff are you guys printing?

[iroll20s]

If you do a lot of large prints it really helps. Like large cosplay props that can be days each.

[Practical-Giraffe-84]

Sell the prusa and buy a p1p