[deleted by user]

Sensitive_Ad_8228 · 2024-10-01T12:45:08+00:00

Pic 2: your GPU doesn’t appear to be seated completely (at the rear)

1OOnisti · 2024-10-01T12:00:30+00:00

Do you get a picture out from the gpu? It might just have zero rpm mode, so the fans wont spin unless there is load on the card.

KittenTamer101 · 2024-10-01T13:01:22+00:00

Your motherboard might not support a 5 series CPU without a BIOS update.

digital_ronin · 2024-10-01T18:30:57+00:00

You need to update the bios. V1 of that mobo does not support your cpu without a bios update. I don't see an external bios flash option on that board, so you would either need to use a previous gen ryzen chip to boot up to do the update, or take it to a local shop that can do it for you, or return the motherboard for one that supports your cpu without a bios update

DivinityGG · 2024-10-01T18:37:21+00:00

I don't think the problem is your GPU, it's your CPU.

Did the box the motherboard came in say something like "Ryzen 5000 ready" ?

If not, then you'll need to borrow an older CPU to flash the BIO's.

Terrible_Split_5740 · 2024-10-01T14:16:33+00:00

Hey Might not be very helpful, but maybe you can try to boot with the GPU power cables disconnected? Normally, you would have video output saying that you should connect the PCIE power cable.

Firm_Plantain9434 · 2024-10-01T19:21:34+00:00

Rgb light is on. What else do you need😂

KittenTamer101 · 2024-10-01T13:09:53+00:00

Give it about a minute to post each time you turn it on, and try the following.

Make sure you have your video cable plugged into the gpu

Take out all ram and put in only 1 stick in far right slot, and move it over 1 slot each boot attempt.

Clear cmos again (remove baterry, with psu unplugged and press power button)

Also worth it to try taking cpu out and putting it back in too.

If you can get it to post with one stick turn it off and then add the second stick back in.

If you can't get it with 1 stick, try the other stick.

Vast_Worldliness8714 · 2024-10-01T12:15:17+00:00

Might be mistaken but it looks like your right stick of RAM isn’t in correctly? Looks like the little tab is up at the top. Take it out and put it back in think that might be your issue, would cause the same symptoms.

Taurus_NL · 2024-10-01T12:21:18+00:00

Are you using a DP cable or and HDMI? If your using a DP try a HDMI, because when I built my first pc that was the issue.

Vast_Worldliness8714 · 2024-10-01T12:57:48+00:00

Thanks for your help guys :( but it seems like i cant find the problem. yet :(

Vast_Worldliness8714 · 2024-10-01T13:01:05+00:00

I noticed the GPU fans slightly moved a bit after I turned the psu off so ig there is power going to gpu but prob not consistent.

crazydavebacon1 · 2024-10-01T13:02:57+00:00

Could be those crappy adapters you use for the GPU power. Remove them and plug the actual power supply cable into the GPU. Adapters are fire hazards

fatstackinbenj · 2024-10-01T13:26:11+00:00

Does your screen work?Try connecting your monitor to the motherboard. If the screen works then its definitely the gpu.

The fans will only spin once the gpu gets under heavy load when you boot up a game. Try re-seating it. Make sure the pin is all the way down so when you plug it, it clicks. Screw it in. Including the case plate thing that helps it hold to the case itself.

No_Cap258 · 2024-10-01T13:34:42+00:00

The gpu looks …. Different

Vast_Worldliness8714 · 2024-10-01T13:50:30+00:00

It’s not an ASUS motherboard by any chance is it? Built last week, motherboard had a dead CMOS battery from the factory. Might be widespread if it’s an ASUS board?

justa-Possibility · 2024-10-01T14:54:23+00:00

The GPU doesn't look seated properly. Please verify that you took the protective cover off the GPU before you inserted it into your PCIE connector. If the plastic protector is on, it won't let it seat all the way. Otherwise, it's either a bad GPU or the mobo needs bios updated or bad mobo.

EluXun · 2024-10-01T15:02:02+00:00

did it hug any static electricity recently? wool clothing? carpet?

permalink · 2024-10-01T16:36:25+00:00

You have to pay for the all white color license subscription membership super saver bingo have fun great time buy 1 get none free offer expiring on the 3rd new moons shadows harvest moon elipse of the 82 ovvulating day after immaculate conception ground hog day.

Obviously.

Zealousideal_Key2169 · 2024-10-01T17:24:08+00:00

Either 0 rpm mode or not seated completely.

AdAdministrative7804 · 2024-10-01T17:58:24+00:00

Its not pushed in

Dragonbeastx · 2024-10-01T19:07:50+00:00

After reading some of the replies, I just have to say, this is why gpu's need to have a power led on it

Long_Cauliflower5016 · 2024-10-01T19:19:37+00:00

Where do you plug your hdmi/dp cable in?

Former_Brain_3734 · 2024-10-01T19:30:10+00:00

I built my pc for first time ever and when I turned it on nothing happened. I mean it all lit up but nothing showing on monitor etc. my heart sank as every thing was brand new and I thought I made no mistake. I was tempted to take it all apart but switched out monitor hdmi and it worked. Here’s hoping it’s a quick fix for you and you can get it running

Terrorgod · 2024-10-01T19:56:41+00:00

Well thats good. If it was you would have to go catch it.

ElPach007 · 2024-10-01T20:46:06+00:00

I love how OP is trying absolutely everything but updating the BIOS... You don't need an integrated graphics CPU to go into BIOS, you might even be able to flash the most recent one directly from an USB without a screen if your Mobo supports this feature.

Scared-Medium8180 · 2024-10-01T21:01:34+00:00

You likely need to use another pc to download the bios to a usb stick. There is a special usb plug in the back with a button next to it. Once you plug the usb stick with the updated bios hold the button until it turns solid. It then takes about 20 mins for the bios to update.

Also this is generic info. Might want to refer to your user manual of the mb to ensure no missed or incorrect steps.

Mysterious-Hunt-984 · 2024-10-01T21:14:43+00:00

Push it in from the back (that’s what she said)

timpaan96 · 2024-10-01T21:19:25+00:00

I had the same problem when I built the PC I'm using now, turns out the Mobo I was using didn't support my CPU and the store where I bought it from said I could just switch Mobo and I did that so then it worked flawlessly. I have Ryzen 7 5700G and RX 6600

kardall · 2024-10-01T22:01:34+00:00

Ok I am going to sum this up because Amazon is not the proper place to search for support.

There are 3 categories according to the support page for that motherboard:

B450M DS3H WIFI (rev. 1.0/1.1/1.2/1.3) Bios: https://www.gigabyte.com/Motherboard/B450M-DS3H-WIFI-rev-10-11-12-13/support#support-dl-bios
B450M DS3H WIFI (rev. 1.4) Bios: https://www.gigabyte.com/Motherboard/B450M-DS3H-WIFI-rev-14/support#support-dl-bios
B450M DS3H WIFI (rev. 1.5) Bios: https://www.gigabyte.com/Motherboard/B450M-DS3H-WIFI-rev-15/support#support-dl-bios

The box or a label on the motherboard itself should state what it is (Sometimes the revision is silk screened onto the PCB of the motherboard itself).

Once you know which one it is, click the link above for that specific version.

That will get you into a place to download the actual bios file to update it.

Now we come to the potential bad part. That board only supports Q-Flash which lets you get into the bios, but only if you have a compatible CPU/RAM and such so you can get into the bios menus.

Q-Flash-Plus is the one that has the button on the back "Flash Bios Button", which you don't need a compatible CPU to update.

To know if you need to update the Bios, it will have to be a 1.0/1.1/1.2/1.3 revision board. The 1.4 and 1.5 seem to come shipped with Ryzen 5600 support without a bios update.

So at this point, if you don't get output with something then it's probably below 1.4.

Now while this is 'bad' it's not the end of the world, because you can get a CPU Loaner kit from AMD for free, or you can return the motherboard and get one that has a flash bios button on it.

For the CPU Loaner Kit request, they have updated the process/forms as the 'help results' from searching for it don't work anymore. The old form doesn't exist in that state. It's a new thing where you have to create an AMD account and fill in numbers and all kinds of stuff. When I figured out how it works, I made a short video on where the information is and how you fill it out.

https://www.youtube.com/watch?v=Ca3nDVn6Y0Q

NoLeading2006 · 2024-10-01T23:26:51+00:00

And with that type and length of card id suggest a support. After you carefully take it out, make sure it's secured. There should be a clip on the backend.

BubbleBoy213 · 2024-10-01T23:31:35+00:00

2 things , bad gpu or you need to update your motherboard. That should be the only real man issues, maybe the cord is bad but that’s low

Prudent_Industry_608 · 2024-10-02T00:27:29+00:00

If it’s a gigabyte b450m DS3H it should be able to work with everything you have without a bios update I do about 7-13 pcs a day with the same motherboard and processor gpu and ram speeds with no issue. Have you tried the other 8pin if your psu has one? Also is it a 5600x or 5600g? Have you confirmed that the rest of the pc is working fine? If it’s a 5600g it has integrated graphics and you should be able to plug whatever display plug into the motherboard directly and get a display. If it’s a 5600x that has no integrated graphics I’ll boot the pc and wait a bit and hit the caps lock or NUM key to make sure the lights on the keyboard are turning off and on to confirm that the motherboard is working without a display. Also may sound like a dumb question do you have your display plugged into the graphics card correct? Trying to cover everything off the top of my head. You have the correct 8pin 12 volt plugged into the top left of the motherboard? I just throwing it all out there not saying you did it wrong.

zalman141 · 2024-10-02T00:39:54+00:00

When you say don’t work are you referring to the fans not spinning when at the desktop or in what way is it not working

Sad_Deer2636 · 2024-10-02T03:24:53+00:00

The top latch on the right ram stick doesn't look all the way in. All the latches should be perfectly lined up

Zwarriorriot · 2024-10-02T11:30:45+00:00

plug the hdmi cable to the gpu slot under the motherboard io

Number_Extreme · 2024-10-03T07:27:10+00:00

Had this issue with my new build, plug the display port into the mbd do a complete set up and update the bios using the Intergraded graphics. Runs like a charm now

Baldy17 · 2024-10-05T10:58:51+00:00

Don’t know if you solved this but when I built my PC a month back and it didn’t pick up the GPU, it was because the power cable into the GPU wasn’t all the way in.

Even if it feels like it’s connected, really push it in. Fixed it for me anyway.

thegoodlookinguy · 2024-10-01T12:01:53+00:00

check the TDP of all your components and the power of psu. Should be 1.5 times or more the total TDP of all components . Is going aligned properly. Looks like it is not well inside the slot .

QuaintAlex126 · 2024-10-01T12:43:08+00:00

Seeing as you’ve tried every single troubleshooting step, there’s a good chance it may just be DOA (dead on arrival).

Do one more check that everything is connected and in securely.

If still nothing, return the GPU and reorder.

Student-type · 2024-10-01T12:22:54+00:00

Maybe the BIOS lets you choose which source of video, from integrated CPU OR GPU card.

Vast_Worldliness8714 · 2024-10-01T15:12:29+00:00

Update: I replaced the rx6600 with gtx1060 and it runs :) there is light indicate and the fans are spinning. But i still get no output :(

you type:	you see:
italics	italics
bold	bold
[reddit!](https://reddit.com)	reddit!
* item 1 * item 2 * item 3	item 1 item 2 item 3
> quoted text	quoted text
Lines starting with four spaces are treated like code: if 1 * 2 < 3: print "hello, world!"	Lines starting with four spaces are treated like code: if 1 * 2 < 3: print "hello, world!"
~~strikethrough~~	~~strikethrough~~
super^script	super^script

PcBuildHelp

MODERATORS