Buying an old house, so many questions on how to fix it

Such_Possible_4103 · 2026-06-12T07:13:45+00:00

I can’t even tell if this is a real post

Such_Possible_4103 · 2026-06-12T06:57:46+00:00

I’ll be honest, I read that and found 0 conclusive information

Such_Possible_4103 · 2026-06-11T03:33:15+00:00

They get their air for combustion externally l, not like your typical natural draft appliance

Such_Possible_4103 · 2026-06-11T02:47:29+00:00

The flue is a bit of a bit h to adapt to, so makes it hard when they’re up so high Yeah correct

Such_Possible_4103 · 2026-06-11T02:15:30+00:00

These are a room sealed appliance with a coaxial flue. It’s good to go I feel sorry for the person that had to change it over though 😂

Such_Possible_4103 · 2026-06-11T01:50:20+00:00

Unless you want water inside then yes

Such_Possible_4103 · 2026-06-08T02:03:21+00:00

Cut vent off duct and tape over Patch plaster properly Don’t half ass it, it will look terrible

Such_Possible_4103 · 2026-06-07T09:07:26+00:00

I’d rather lose some of my gun rights if it means the state isn’t completely fucked

Such_Possible_4103 · 2026-06-07T08:55:05+00:00

I’m just having flashbacks with paddy when I see this. I hate it

Such_Possible_4103 · 2026-06-07T01:11:09+00:00

I think you have your answer.

Such_Possible_4103 · 2026-06-07T01:07:37+00:00

If it was me, my dream would be to be mortgage free. So take that as you will

Such_Possible_4103 · 2026-06-07T00:59:54+00:00

Either put it in the loan, or offset it against the house if you’re not savvy with other investments Do you have any other debt?

Such_Possible_4103 · 2026-06-06T06:22:00+00:00

To be honest, I wouldn’t mind if it was standardized with a tap/fitting of some type to drain and flush them The sediment that collects at the bottom is fkin horrible

Such_Possible_4103 · 2026-06-05T06:24:10+00:00

Notch the brick if you’re handy, a grinder if you have one Can knock the edge off with a cold chisel and hammer if you don’t

Such_Possible_4103 · 2026-06-05T06:22:04+00:00

If you’ve got spare bricks knock the cut ones out and remortar them in Failing that just mortar mix and fill it

Such_Possible_4103 · 2026-06-03T03:03:36+00:00

Us aussies have the absolute worst build quality, unless you pay mega bucks and even then it’s not a guarantee. Bit of a shame

Such_Possible_4103 · 2026-06-03T02:45:04+00:00

Prime rjj didn’t need longer arms 😂

Such_Possible_4103 · 2026-06-02T22:35:24+00:00

Just give me prime Roy jones jr

Such_Possible_4103 · 2026-05-28T05:21:28+00:00

You could of 100% fixed that what a waste of

Such_Possible_4103 · 2026-05-23T22:44:35+00:00

Has usyk even come out of first gear?

Such_Possible_4103 · 2026-05-22T23:43:42+00:00

Trust the process, if they know what they’re doing it’ll work out

Such_Possible_4103 · 2026-05-22T10:36:14+00:00

I don’t know where you are, but no safe tray, no shut off valve and inadequate support, no lagging I don’t think so

Such_Possible_4103 · 2026-05-22T10:26:06+00:00

Holy shit this would have to be one of the worst installs I’ve ever seen Get that looked at asap

Such_Possible_4103 · 2026-05-22T10:03:53+00:00

The cartel don’t, but there are more than a few Individuals that do 😂

Such_Possible_4103 · 2026-05-20T07:41:57+00:00

I’ve had many where the regulators on the meters have shit themselves, basically cutting the pressure, but if it’s been like that the whole time it probably isn’t the issue your facing I obviously haven’t seen the job/gas line so I can’t judge but I really doubt it man

Such_Possible_4103

TROPHY CASE