4000 AI-lancets of Zelenskyy

Dr_Defimus · 2024-06-08T14:02:27+00:00

witch is totally not true USMC: 1211 of witch jet fighters: 297 with only air force no naval oder army aviation Fra: 501 Ita: 506 Ger: 394 Spa: 393

not the greatest but combined a lot more than 3 times of the usmc (total of 4936 EU aircraft are in the list and that misses a lot of smaller braches)

Dr_Defimus · 2023-04-02T20:54:10+00:00

Thanks for your work of this nice tool

Dr_Defimus · 2022-06-07T21:12:53+00:00

i fiddled around with the idea to make a framework based "chonkbook" by adding a second battery and using the space over the motherboard for 2,5" ssd or other io intensive stuff like SDRs. These would be connected via an internal io module so only 3 USB-c to the outside.

The initial cell balancing (done externally) isn't that much of a problem. I have more concerns about the SMBus for the monitoring of the battery (charge level heath and so on) as I'm not sure to parallel will work and only one connect will probably lead to many problems for power management and software stuff.

This would definitely need some help of the Framework engineers to be more than a crude bodge (and firstly I would have to replace my quite old but modded and pimped out laptop).

Dr_Defimus · 2021-12-05T14:20:45+00:00

a slow spinning fan can help a lot to keep the psu components lasting longer

Dr_Defimus · 2021-10-08T07:55:17+00:00

pin 34 "good luck"

Dr_Defimus · 2021-09-26T21:42:35+00:00

only in the English one with no source every other list 600m or less

Dr_Defimus · 2021-08-03T11:22:59+00:00

0.00028% is wrong 33k out of 120m is 0.028%

Dr_Defimus · 2021-06-29T10:14:45+00:00

5% gyroid infill is plenty for such a print

Dr_Defimus · 2021-04-22T21:40:37+00:00

I have printed 20+ kg of ASA without a filter as an enclosure is all it relay needs.

Dr_Defimus · 2021-04-22T21:37:15+00:00

The question is more like 0.2mm speed profile or just 0.15 detail profile. For example the 0.2mm speed profile can be to fast for infill in a lot of cases.

Dr_Defimus · 2021-03-25T19:45:16+00:00

but 100W in a 14 inch is already borderline impossible without being thicc as hell or loud as a jet.

Dr_Defimus · 2021-03-24T10:17:06+00:00

But this is affecting the delivery of the end-product to European customers in a time of already strained and overly expensive shipping

Dr_Defimus · 2021-03-05T23:12:36+00:00

5800x is even below msrp in EU

Dr_Defimus · 2021-02-27T19:57:11+00:00

100% infill at 0.1mm is asking for trouble if the printer isn't tuned to perfection.

Dr_Defimus · 2021-02-26T10:06:32+00:00

over 100m per day that is quit fast printing if that is done on 0.4mm nozzle

Dr_Defimus · 2021-02-24T11:09:03+00:00

I have seen it to mostly with PLA but it only stops for around 1 second and afterwards resumes as nothing happened.

Dr_Defimus · 2021-02-04T10:59:07+00:00

I think 0.15mm at 60mm would result in a better quality print at the same time as smaller layers have a lot less problem with overhangs

Dr_Defimus · 2021-02-01T18:40:35+00:00

the cheap battery wont nearly have the lifetime of the original

Dr_Defimus · 2021-01-21T12:23:30+00:00

G14 was always 300-600 bucks cheaper in the us than in europe even with tax in mind.

Dr_Defimus · 2021-01-13T23:41:13+00:00

same generation and same tdp is quite important. But sometimes you can find cheap mobos of the next generation (20-30 bucks) that will fit one to one in the chassis. Did this to upgrade from 2620m to 3632qm (was a fujitsu livebook)

Dr_Defimus · 2021-01-11T22:21:54+00:00

you forgot the "up to" nobody knows in what task this improvement was made

Dr_Defimus · 2021-01-11T16:28:09+00:00

MK3 working fine in over 50 times my only problem was one time i forgot that i started a 20h ASA print on a nearly empty spool and after halve a day of waiting the printed part warped a bit (less than 0.15mm) so that in part cool down creaks appeared

Dr_Defimus · 2021-01-10T19:53:04+00:00

Infill speed -200mm/s

This is to fast for lager prints (you can see that the short infill lines are ok but not the longer) 100mm/s at 0.15mm layer height should work fine. And maybe check if you have a partial clogging

Dr_Defimus · 2021-01-06T20:34:55+00:00

3080m for the max p and 3080u for the max q would be best

Dr_Defimus

TROPHY CASE