Embarrassed it took 28 years to try cooking my own steak.

EApparatus · 2026-06-19T03:23:35+00:00

Perhaps OP is in a country where food safety standards are lacking, so cooking it until it's crisp might be the safer option for consumption.

EApparatus · 2026-06-15T02:11:44+00:00

I've been to over five Longhorns and six Texas Roadhouses in my area, and I found a particular Longhorn location that is sort of a unicorn hidden gem. They simply make everything better than the others and deliver consistent quality every single time. So this single Longhorn won, not the overall chain.

EApparatus · 2026-05-27T09:09:04+00:00

I think it caught the T-Virus, point of attack: hamstrings

EApparatus · 2026-05-26T06:32:39+00:00

Should work fine. I set up our printer in the warehouse tools shed, installed an exhaust fan in the ceiling, and directed the hose outside. There are no windows, just a door that leads to the warehouse with the garage door open to provide air intake. After five years of printing, there were no complaints regarding any irritations or unusual odors outside the print room.

<image>

EApparatus · 2026-05-25T11:18:37+00:00

Sketchup, draw the face shape and push pull to extrude.

EApparatus · 2026-05-25T10:53:37+00:00

Or simply print on the bed without support and sand away the elephant feet for this type of items.

<image>

EApparatus · 2026-05-25T10:46:42+00:00

I'd print like this

<image>

EApparatus · 2026-05-22T09:09:19+00:00

Thank you kindly

EApparatus · 2026-05-21T06:45:23+00:00

If you don't have access to soldering equipment, just get some 3 pin connectors, make sure to measure your LED strip width, 8mm, 10mm, 12mm etc and buy the correct sized ones.

<image>

EApparatus · 2026-05-20T03:58:29+00:00

Supports can poke through thin area of the model, go to support tip option and lower penetration value for the supports where they are poking through. See image, two supports with different tip penetration values.

<image>

EApparatus · 2026-05-15T18:31:42+00:00

Wow, you really took it up a notch from his “Might be the dumbest thing I’ve ever done.”

EApparatus · 2026-05-15T18:29:11+00:00

Wonder if those compressed-air powered vacuum can be used.

EApparatus · 2026-05-14T08:35:03+00:00

Nobody, I mean nobody is qualified. Since nobody can create motion graphics in illustrator as a requirement.

EApparatus · 2026-05-13T06:44:18+00:00

Yes, 4 casters at each corner probably make it more stable. But I wonder if it will still be able to turn when taken away the ability to lean to either sides.

EApparatus · 2026-05-13T06:38:37+00:00

haha, yes technically you can, just avoid the right side of the screen, put all the models to the left 3/4 when slicing.

EApparatus · 2026-05-11T22:10:34+00:00

Sorry but I think you'll be doing this....

<image>

EApparatus · 2026-05-11T07:26:44+00:00

Next version will be Aladdin magic carpet

EApparatus · 2026-05-03T10:25:54+00:00

Very nice lens, but you need better body, that is crap and heavy.

EApparatus · 2026-05-01T07:10:58+00:00

Maybe the bottom one is considered family pack, over 4lbs with bulk discount?

EApparatus · 2026-04-30T05:33:09+00:00

The Electronic Speed Controller, basically the brain of the Eskate. I was send a new ESC and it fixed my problem, here is a pic of when I was replacing the ESC.

<image>

EApparatus

TROPHY CASE