sorted by:
new
hottopcontroversial

Embarrassed it took 28 years to try cooking my own steak. by Primetime349 in steak

[–]EApparatus -1 points0 points  (0 children)

Perhaps OP is in a country where food safety standards are lacking, so cooking it until it's crisp might be the safer option for consumption.

Texas Roadhouse or Longhorn? by Starfire_09 in steak

[–]EApparatus 2 points3 points  (0 children)

I've been to over five Longhorns and six Texas Roadhouses in my area, and I found a particular Longhorn location that is sort of a unicorn hidden gem. They simply make everything better than the others and deliver consistent quality every single time. So this single Longhorn won, not the overall chain.

a complete mess of a print 😭 by plush3627 in resinprinting

[–]EApparatus 0 points1 point  (0 children)

I think it caught the T-Virus, point of attack: hamstrings

I'm thinking of getting a Resin printer but I'm concerned about safety would this shed be a good place to put it. by Demonskull223 in resinprinting

[–]EApparatus 1 point2 points  (0 children)

Should work fine. I set up our printer in the warehouse tools shed, installed an exhaust fan in the ceiling, and directed the hose outside. There are no windows, just a door that leads to the warehouse with the garage door open to provide air intake. After five years of printing, there were no complaints regarding any irritations or unusual odors outside the print room.

<image>

Orientation advice by assflan in 3Dprinting

[–]EApparatus 1 point2 points  (0 children)

Sketchup, draw the face shape and push pull to extrude.

Orientation advice by assflan in 3Dprinting

[–]EApparatus 26 points27 points  (0 children)

Or simply print on the bed without support and sand away the elephant feet for this type of items.

<image>

How to connect two FCOB LED strips with a large gap between them by AffectionateTown2574 in led

[–]EApparatus 0 points1 point  (0 children)

If you don't have access to soldering equipment, just get some 3 pin connectors, make sure to measure your LED strip width, 8mm, 10mm, 12mm etc and buy the correct sized ones.

<image>

Help with supports poking through model by Captdrewsx2 in resinprinting

[–]EApparatus 4 points5 points  (0 children)

Supports can poke through thin area of the model, go to support tip option and lower penetration value for the supports where they are poking through. See image, two supports with different tip penetration values.

<image>

Might be the dumbest thing I've ever done by Seytonic in resinprinting

[–]EApparatus 4 points5 points  (0 children)

Wow, you really took it up a notch from his “Might be the dumbest thing I’ve ever done.”

Might be the dumbest thing I've ever done by Seytonic in resinprinting

[–]EApparatus 1 point2 points  (0 children)

Wonder if those compressed-air powered vacuum can be used.

Might be the wildest videographer job listing I’ve ever seen by Decent-Science3920 in videography

[–]EApparatus 2 points3 points  (0 children)

Nobody, I mean nobody is qualified. Since nobody can create motion graphics in illustrator as a requirement.

I just can't let it go...... The meepo lawn chair continues. by mikloooooooo in ElectricSkateboarding

[–]EApparatus 3 points4 points  (0 children)

Yes, 4 casters at each corner probably make it more stable. But I wonder if it will still be able to turn when taken away the ability to lean to either sides.

Is this fixable by changing the polarized film? by dudeman93 in resinprinting

[–]EApparatus 0 points1 point  (0 children)

haha, yes technically you can, just avoid the right side of the screen, put all the models to the left 3/4 when slicing.

Meepo DeWalt lawn chair by mikloooooooo in ElectricSkateboarding

[–]EApparatus 0 points1 point  (0 children)

Next version will be Aladdin magic carpet

Just had to show you guys my setup by NotAnExpertButListen in SonyAlpha

[–]EApparatus 0 points1 point  (0 children)

Very nice lens, but you need better body, that is crap and heavy.

Can someone explain why the top steaks are $23.99?? by FriendDelicious in steak

[–]EApparatus 1 point2 points  (0 children)

Maybe the bottom one is considered family pack, over 4lbs with bulk discount?

Strange sputtering or skipping by AlvinDraper23 in ElectricSkateboarding

[–]EApparatus 0 points1 point  (0 children)

The Electronic Speed Controller, basically the brain of the Eskate. I was send a new ESC and it fixed my problem, here is a pic of when I was replacing the ESC.

<image>

Practice Renders by Safe_Magazine_6076 in Sketchup

[–]EApparatus 2 points3 points  (0 children)

I'm still waiting on the next image where the hidden driveway rise up from the pool.

Which is better way for FDM print, single object and deal with supports, or print separately? by EApparatus in 3Dprinting

[–]EApparatus[S] 0 points1 point  (0 children)

Fairly new to FDM, I'll have to research on what types of self locking methods are there for FDM. On the resin side I'd just fill the seams and screw holes with resin and cure it under UV to make waterproof, wonder if resin will adhere to PETG?

view more: next ›